Quick Question!

Have you ever purchased from PartSelect.com before?

Models > GWSE5240H1WW > Parts

GWSE5240H1WW General Electric Washer - Parts

All parts for the General Electric Washer GWSE5240H1WW

Below is a list of all parts for the General Electric Washer GWSE5240H1WW. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the GWSE5240H1WW
1-14 of 122
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.38

Tub Dampening Strap

The tub dampening straps support the wash tub and reduce vibration by keeping the tub at the center of the cabinet. If your washer shakes and moves, or is making a loud banging noi...

$34.43

Agitator

This is a dual-action agitator for a washer. This is an OEM replacement part that is sourced from the genuine manufacturer. The agitator tosses your clothes to clean them efficiently. This plastic dual-action agitator is white in color. It is approximately 18 inches tall with a base diameter of about 12 1/4 inches. No tools are required for this repair. Your agitator has eight tabs that fasten on the drive block of your washer, which is driven by the transmission. This part does not include the agitator coupling kit, which is frequently purchased at the same time as the agitator.

$12.88

Drain Hose - 4 1/2' Long

The drain hose is black in color and made of flexible material. This is a part for your top-load washer. The hose measures 57 inches long. This part moves the water out of the wash...

$7.52

Tub Seal

The main tub seal is located between the transmission and the outer tub. Its the primary water seal in the outer tub for the transmission-shaft. If your washer is leaking during the fill cycle, or at agitation time, your tub seal may need to be replaced. You can check if the tub seal needs to be replaced by watching that area during an actual fill cycle. Take off the front panel, or if it is a front-loading washer, the rear panel. Without touching the washing machine, observe the place where the shaft of the transmission comes into the tub and the weep holes at the housing of the rear bearing. If there is water leaking, the tub seal is at fault. NOTE: This seal is difficult to replace and should probably be installed by a qualified technician.

$12.78

6-Rib Drive Belt

This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.

$57.04

Drain Pump and Motor Assembly

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. If you notice that your washing machine will not drain, there is a good chance that you will have to replace the drain pump. The drain pump is located inside the washing machine, near the bottom. To access the drain pump for this repair, you will need to remove the front panel. Before you begin this repair, be sure that the power source is disconnected and the water source is shut off.

$3.29

Tub Bearing

This is a tub bearing and it is meant to work in conjunction with your washing machine. The purpose of this part is to aid in keeping the inner tub of your washing machine spinning...

$4.48

Split Ring

This split ring is two inches in diameter.

$3.90

Drain Hose Clip

This drain hose support clip is a piece for your washer. The purpose of the drain hose support clip is to hold the drain hose in place by attaching to a cabinet. This piece is off-...

$8.41

Hub Nut

$18.30

Tub Bearing

$7.59

Agitator Coupling

Bolt not included. This part connects the transmission drive shaft to the agitator base.

$3.69

Hub Washer

$18.26

Lid Switch with Wire Harness

This lid switch with wire harnesses is used in washing machines. The pin on the lid switch pushes onto the lever of the switch to communicate to the machine that the washer lid is closed. If your washing machine is not running when the lid is closed, not spinning, draining, or agitating, replacing the lid switch could solve the problem. The tools needed for this repair are: putty knife, 1/4 inch nut driver, wire strippers and crimpers. Refer to the manual for further installation instructions. Remember to unplug your washer from the power source as a safety precaution.

All Parts for the GWSE5240H1WW
1-14 of 122