Models > GU2400XTPS3 > Instructions

GU2400XTPS3 Whirlpool Dishwasher - Instructions

All installation instructions for GU2400XTPS3 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GU2400XTPS3
466-480 of 488
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

rinse cap came off and melted.

  • Customer: Virginia from Vestal NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just screwed it on. Really impressed with fast service getting it to me.

start did not work ...drain motor did

  • Customer: Ronald from Arlington Heights IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
followed instructions to take off front panel. popped out the bad fuse assembly (need flat blade to pry it out) & popped in the new one. no need to cut the wires & use the supplied ones since the dishwasher had the correct ends. it is good to have the wire leads just in case.

small leakage of water from bottom right door.

  • Customer: Jan from Montgomery AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I replaced the door gasket. This was easily done. First I removed the old gasket by simply pulling it out, no tools needed. The gasket is simply resting in a slot. Then I installed the new gasket by pushing it into the same slot, after I had thoroughly cleaned it with vinegar. I did not need to trim the gasket at all; it fit perfectly.

Detergent door would not open during wash cycle.

  • Customer: David from Warren PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed door screws and door cover. Unplugged wire from old dispenser then remove dispenser screws and dispenser. Connector did not match male plugs on new dispenser. Installed new female connectors on wires then reassembled dispenser and door. worked correctly after completion.

Dishwasher spinner fell off. Wore out. Needed replacing

  • Customer: Rebecca from Sacramento CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
My son Eric, read the directions and followed every instruction. Job was complete in less than 15 min. I filled dishwasher and set it to clean. Worked perfect and dishes came out sparkling. Thank you for you service. My ordered part was here overnight and instructions were easy and clear. Rebecca

The old panel board fried and I had to replace it.

  • Customer: Kelly from Tatum TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
THIS WAS SO SIMPLE!!! First, I unplugged my dishwasher so I wouldn't take the chance of electrocuting myself! I took the star shaped screws out (special type of screws that required a special set of screwdrivers, we owned them already), unplugged all of the wires from the electronic control board, popped the new one in, plugged it up to the wires, plugged the dishwasher back in, and turned it on!!! Works beautifully!!! Thank you Sharon for all of your help!! Great customer service!

A rat chewed three hoses, but luckily did not chew the water supply!

  • Customer: BARBARA from SLIDELL LA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Start by removing the dishwasher from cabinet. Oh, don't forget to turn off water supply and also don't forget to install a plug on garbage disposer so when your other half uses the sink while you are outside you don't end up with a leak! Both supplied hoses installed easily, the third which I used semi flexible clear tubing with clamps deemed more difficult to bend, so I soaked the hose in very hot water to make it more pliable thus making the bends easily. I then had to wait until I was sure I captured the culprit before re-installing the unit.Your sales person was very informative and knowledgable and helped immensely!

leak @water inlet valve

  • Customer: brian from madison WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench set
  • 0 of 0 people found this instruction helpful
pull unit out laid it down on it side replaced part reversed bingo all done 30 min tops

No water pressure in upper or lower diswasher spray arm assemblies

  • Customer: Terry from Huntley IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
The Parts select video instructions for this part are pretty much spot on. The grinder assembly broke where it attached to the circulator pump impeller shaft. The screen became totally clogged and thus no water pressure to the diswasher spray arms. The only thing Id add would be to verify the circulator pump impeller is in good shape after removing the old grinder assembly and that you are able to rotate it by hand in case the impeller motor itself is seized or the impeller is jammed. Once the grinder assy was replaced good water pressure and cleans like a champ.

heating eleament broke

  • Customer: don from jackson AL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
My dish washer is a under the counter type.On mine there are two screws that screw into the bottom of the counter frame,these are located inside when you open up the door, they will be right on the inside and to the very front of the upper part of the door opening. Remove both screws. Now,be slow and start to pull the unit out from under the counter. Make sure you don't scrastch your floor,you may use a towel.If your dish washer's discharge hose is conected under the sink, go ahead and remove it. If your unit can be unpluged, unplug it. If not throw the breaker.Try to turn your unit on' if it does you still have power still on. Try again.With the unit pulled out so you can see the back, lay on your side and look for to long looking plastic nuts with a wire coming out of them. These nuts are holding your eleament in place.Unscrew both nuts and let them slide down the wires. Pull both of the wires off the eleament.now reach inside and remove the old eleament.Put new eleamen in place, reconect wires and tighten the nuts,caustion not to tighten nuts to tight.Ok hook the hose and eleectric back up,push the unit under the cabanet, and install the two screws.Really hopes this helps.

Should have been simple repair. Door panel would not come loose. Seems they used adhesive on the door panel and the styraform insulation. Did not want come loose and put back together as I did not want to destroy or bend door panel and insulation. Any advice on how to remove!

  • Customer: Don from La Verne CA
  • Difficulty: Very Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Put back together could not pull apart without damaging door panel and insulation.

Wheel had come off of the adustable top rack wheel assembly

  • Customer: Robert from SALEM IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I am not the greatest at fixing things. Though the instructions were called "really easy", I made it difficult. In fact I broke the first one I ordered and had to reorder. My mistake was I was prying with screwdriver way too hard and broke a piece of it off. So, during the early morning hours on the day after the new part arrived, a still small voice told me what I needed to do. I had put the wheel of the assembly in the track and then tried to make it fit on the wires of the rack. Wrong!! Install the assembly, THEN when you have done that, put the wheel in the track and then put the end cap on and you are done. Piece a cake even if I don't say so myself.

Would not run, the little red light would blink

  • Customer: Vickie from Adona AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My son done the repair for me.

Dishes not clean on top rack. Very little water spraying.

  • Customer: Richard from Saint Gabriel LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the "Installation Video for Chopper Assembly". No problems except chopper cover was hard to remove. Be careful to install new part with gear engaged and screen correctly inserted in grove. See my pic of old clogged screen/broken chopper.

Water inlet valve was leaaking

  • Customer: VICTOR from MEDFORD OR
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I did the repair just like the video instructed
All Instructions for the GU2400XTPS3
466-480 of 488