Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washing machine never stops filling and thus overflows
Removed the screws from the control panel and flipped it open. Used putty knife to pop the retaining clips that held the front panel of the washer in place to expose the drum itself. Noticed black gunk build up in hose connecting the drum to the water level pressure switch.
Disconnected the hose at both ends. Attached the new hose to the pressure switch and proved it was working by blowing into the hose and getting the water to stop flowing into the washer.
Taped the old hose to the new hose so I could use it as a pull-wire to guide the new hose through its protected housing. Attached the other end of the new hose to the tub and voila, all was well.
Drain pump not working. Washer would not drain or advance to spin cycle.
Repair video is spot on but does not emphasize securing the drain pump to the washer before reattaching hoses. This holds the pump in place allowing you to compress the hose clamp while pushing on the hoses.
Washer lid sensor stopped working, thus, would not spin, thinking lid was open
This was easy and took maybe a half-hour. The harder part was pulling the front panel off (up) to access the insides. Simply snipped the wire to the old sensor and spliced the new wire and inserted the new sensor. Worked perfectly and saved me $400? on a new washer! (Cover panel is slightly bent, did not re-snap in, so it's loose; I don't care about the looks, so I will screw metal screws using a hinge to close it.)
Removed the front panel (retainer clips), removed two screws holding the top panel and door, removed all 4 dampening straps and replaced them with the new straps, put the components back in reverse order of removal.
Hose had developed a slit in the seam nearest to the tub and was pouring out the water flooding the basement where the washer is located.
Lay the drain pipe lower than the tub to remove any excess water in the tub and lines. Loosened clamp on the tub side with a screwdriver then removed hose from the tub. I used pliers to pinch clamp and remove hose from pump. To install hose put clamps on hose then mount to the pump and the tub then tighten clamps.
A lot of water was coming out underneath the equipment.
Steps: 1.- Open the front panel by pressing down (with a spatula) the 2 metal locks located between the front and top panels. 2.- Remove the drain hose located int the lower right and at the bottom using a set of pliers and a nutdriver. 3.-Install the new drain hose. 4.-Reinstall the front panel
The installation itself took me less tha 15 minutes. Since I had opened the the front panel, I took rthe oportunity to air clean and dust off the equipment.
After noticing the leak, I moved the washer out to try to find the source. In the process, the Drain Hose Extension broke in two. As an emergency repair, I put the two halves together with duct tape. After running the washer again to try and find the leak, I discovered that it must have been the Drain Hose because now there was no leak. I then ordered a new one from PartSelect and replaced it with the repaired item.
turned washer on it side took bottom off removed hose and replaced it with the new one. so very happy i tried it , works great like before. thanks for the easy to find diagram of parts.
Determined the drain hose on the back of the machine was leaking, due to my dog chewing on the hose. Replaced the hose with the new one, locked the dog out of the garage where the machine is located, problem solved.
first I filled the washer max load to determine the problem, once I saw where the water was dripping I decided to remove the hose. I removed bottom of the hose, and the water from the tank started pouring out, I tryed to put the hose back on but started to get a pretty good electric shock, I then unpluged the washer and ran to garage for the floor squeegy. I then pushed the water out the side door. After cleaning and drying all rooms I sat down at the computer and ordered part. When the part arrived I removed clamp with pliers put both clamps on the new hose and installed. A very simple project and I ended up with a clean laundry room. Thanks "Brainy"
I pulled the front off of the washing machine using a table knife to pop the clips. The drain hose had a hole big enough to put your finger in so we knew that was the problem. One of the clamps holding it on took a screwdriver to loosen the clamp, the other I used a pair of adjustable pliers to squeeze the ends together to loosen it. I pulled off the old part, ordered it, got it the next day and replaced it the same way I took it off. It was simple and the part was less than $10.