GTS22JCPDRWW General Electric Refrigerator - Instructions

Unplug refridge then loosened two bolts holding old ice maker. Lower then unplug and removed. Plugged in new harness and tightened two bolts to secure new ice maker. Plug in frig and wait for ice.

removed broken bin , slid new ice bin in closed door. I bought the complete part.

My son did it , and showed me what he did when he was finished.

replaced lights in refrigirator and freezer

Removed the divided glass shelf, to which the slide rail is attached. Removed the broken rail, saved the two screws.
Now comes the clincher:
It would help if the replacement part website would tell you what size and what kind screwdriver you will need, so you could start chasing it while you wait for the part.
Even better if they could include it, since the plastic part and it‘s shipment is not exactly cheap.
So to screw in two screws you need a #15 Star screwdriver!
How many housewife’s have this one in the tool drawer?

I watched the video provided by PartSelect twice, then proceeded with the removal and installation. It took me 40 minutes from start to finish. Piece of Cake. Everything works fine now.

The original design is poor. The evaporator fan is mounted in an upright position just below the ice-maker. A plastic grate mounts over the fan assembly to allow for air circulation. Unfortunately, random chips of ice from the ice maker can fall into the fan, causing the fan to shear its blades. Replacement of the fan blade is relatively simple (accept for having to completely unload the freezer and remove all back covers, the ice-maker auger motor assembly, and the metal evaporator cover). In order to mimimze this from reoccuring, I installed a 1/4'' mesh metal screen over the exhaust ports on the cover. Thus far, this has worked well to keep ice chips out of the evaporator fan.

First, remove the cardboard cover on the back, lower portion of the refrigerator.

Next, locate the condensor fan motor assembly and blade. (Right side as you are facing)

Using a pliers, hold the shaft to keep it from turning and prevent damage to the motor. Using a screwdriver, slide the old ring compression on the blade shaft toward the motor (away from the fan blades) to loosen.

Remove old blade from the shaft by firmly grasping the motor shaft with a pliers (to prevent from damaging) and pull the blade assembly off.

Reverse the above steps to attach the new blade.

The icemaker arm disconnected from the metal frame. This caused the icemaker to cycle and the heater to come on and stay on until the plastic parts melted causing a mess and stink. This action melted the ice and then the water fell through the frozen items in the freezer and refreezed in the lower portion. OK, I remover the dead icemaker and tossed it away. I installed the new icemaker and the wiring harness didn't fit right (way to long). I retrieved the old icemaker and removed the wiring harness from it. I removerd the new ice maker and installed the old wiring harness to the new icemaker. I then installed the new icemaker, plugged it in and turned on the power. No water, I ordered the dual solenoid water valve, installed it with difficulty (another story) the turned on the power. I reinstalled the ice bin and found it didn't fit. The icemaker was to low and couldn't be adjusted, 1/4" higher would have been great. I shoved in the bin anyway, I was out of ice for my scotch, and it started making ice.

It was a snap! Literally. We just pulled out the old one, cleaned the track and snapped in the new one

I simply removed the old seal on the refrigerator door and replaced it by just pushing the new gasket seal back into place. It was a very easy repair to do.

Replaced icemaker assembly. Only 3 Phillips screws to remove the old assembly. Pretty much an exact swap. Was easy to replace but the connecting cable on the new replacement assembly wasn't very easy to make fit. Had to force it into a location that would be out of the way and allow everything to operate properly. That connecting cable should be more flexible and adapt to the fridge a little more friendly.

took fan off put on new one reassembled put together thanks works just fine saved 600 bucks

took back cover off. swept the rear with a vacuum cleaner to get rid of dust.found that the fan would not turn. ordered part with your really great ordering technique. Part was suppose to be here in 3-5 days and was here the next day!!!.Removed 2 bolts pulled out the plastic clip that held the wire on. and worked the fan blade off shaft. removed and replaced in the same order as taking simple Thanks

After I have checked oline , I ordered the parts wich Igot a day early and fix it , it took me about 15 minutes and I saved at 250.00 dollars . Thanks for all the help.

J Serpa ,Ma.