This is a duct felt seal for a dryer. The duct felt seal allows the front-load dryer drum to glide smoothly on the front panel. Your dryer will not function properly if the drum felt seal is compromis...
$11.56
In Stock
Order within the next 7 hrs and your part ships today!
This Drive Belt is 89.5" long and comes in black, featuring four ribs on the inside for a better grip. This is a long belt that wraps all the way around the dryer drum, around a tension pulley, and th...
$36.13
In Stock
Order within the next 7 hrs and your part ships today!
If your dryer is excessively noisy when operating, is not tumbling, or is leaving marks on your laundry, it may be time to replace the drum glides. The drum glide bearing is a genuine OEM part for you...
$13.17
In Stock
Order within the next 7 hrs and your part ships today!
This is a replacement O-ring for the drum bearing retainer on your dryer. The drum bearing is found at the back of the dryer drum. The O-ring is designed to create a seal on the drum bearing. The O-r...
$9.01
In Stock
Order within the next 7 hrs and your part ships today!
This part is connected to the rear bulkhead of the dryer with screws. It provides a way of connecting individual electrical wires and offers protection of the device from electrical surges (voltages and/or currents).
$34.29
In Stock
Order within the next 7 hrs and your part ships today!
Questions And Answers for GTD65EBSJ4WS
Ask our experts a question about this model and we'll get back to you as soon as possible!
7 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ronald
August 13, 2021
Why my dryer wont turn its got power
For model number GTD65EBSJ4WS
Hello Ronald, Thank you for writing. The most common reason for a dryer to not tumble is a broken Drive Belt PartSelect Number PS1766009. However, while you have the back of the dryer off, it would be worthwhile to check Idler Arm Spring PartSelect Number PS10059168, Idler Pulley PartSelect Number PS9494502. the Slide Bearings PartSelect Number PS3505464 and PartSelect Number PS4704230 and Top DrumBearing PartSelect Number PS11767002. We hope this helps.
Hello Kathy, thank you for contacting us. According to our research, the dimensions of your model are:
Width: 27 in.
Depth: 30 1/2 in.
Height: 46 in.
We hope this information helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Rosalind
May 10, 2023
I need the serial number for this dryer
For model number GTD65EBSJ4WS
Hello Rosalind, Thank you for writing. The Serial number would be listed on the sale sticker as the model number. We hope this helps!
Clothes are not getting completely dry. Not heating.
For model number GTD65EBSJ4WS
Hello Jonathan, thank you for the question. According to our research, we would recommend checking the inlet control thermostat, part number PS1766014, to fix the issue. We hope this helps!
Hi Ronald,
Thank you for your question. If your dryer will not start, there are some parts that you will need to check to see which one is causing the issue. You will need to check the belt, the door switch, the fuse, the terminal block and grounding strap and the inlet control thermostat. We hope this helps! Good luck with the repair!
Removed the front Dryer panel. Left drum in place and lifted it up slightly to get access to motor drive. Slipped belt in place and put panel back on. This was a first attempt ever at fixing an appliance and it was no big deal.
I had to take most of the dryer apart because there is no rear access to the motor. It turned out to be easy to dissasembel the dryer. The only problem that I had was that I could not figure out how to route the belt around the motor and the idol pullies. I could not find anywhere that gave instructions on how to properly tension the belt
... Read more. I finally figured out that the idoler pulley needs to be locked in place on the right side of the engie mount. Then the belt needs to be routed over idoler pulley and under the motor pulley. Finally release the idoler pully from the locked postion to put tension on the belt. It really turned out to be pretty easy.
Pryed off the top with a flat head screwdriver and removed the 2 screws holding the front panel to the sides. Then lifted the front panel off of the bottom brackets. Belt fit perfectly and followed the provided instructions to loop it around the motor and pulley. PartSelect got the part to me within a couple of days and the repair was a
... Read moresnap.
