GSC308PJT4 Whirlpool Microwave Oven Combo - Instructions

This is the third time that the bulb went out.It took two Sears service technitions to remove the entire appliance out of the cabinet. The entire top has to be removed and the insolation has to be pulled back to get to the electrical wire. I am waiting for an appointment to get Sears to do it again. The door springs have broken and you have to make sure the door is closed before walking away. It has a heavy glass and the weight is pretty heavy. Robert.

Removed the 6 screws securing the door and inner frame unit. Lifted off the frame and inner glass unit. Then, after cleaning all the broken glass, put the new glass in; first reattaching the inner frame and then the outer door cover.

The exact part for this oven is no longer available. I purchased one hat was close in size, but larger than the original. Upper and lower brackets hold the glass in place, so length was not a problem but height was. I removed the upper brackets, re-shaped them with the vise, a hammer and metal shears. The glass would now sit inside the bracket where the screws also went. I had to be quite careful the screws did not shatter the new glass.

The hardest part was aligning the 4 holes for the top brackets. Since 2 holes were on one piece of the door, and 2 were on the other (holding the glass sandwiched between) precision was critical. Also the screw length was critical because the glass now sat in a area where it could come in contact with the screws. (I know - pictures would be most helpful, and I didn't take any.)

Using tape and lots of patience, I got the holes aligned. I covered the old holes inside the oven door with spare screws. I filed down the points of the sheet metal screws so that, if they contacted the glass, they would not be pointed.

Once everything was reassembled, I turned the oven on high for about 1/2 hour to ensure the heated metal and glass all played nicely together. We've had no problems in the month since the repair.

The other comments from folks who had done this were very helpful!
I had to go look up the directions for removing the door. To do this flip the latches on the hinges and then close the door as far as you can and pull up, it will come out.
Now lay the door flat on the kitchen counter and take out the 6 screws you can see on the edges and inside of the door. They are all the same so you don't have to keep them organized. Now you can take off the outer door with the handle (lift the inner door out since you will have the door face down at this point) and get it out if the way. Remove the hinges and set them aside but don't get them mixed up.
Next, take out the screws on the inner glass rails, there are two rails. Keep those rails in order for replacement. Take out the middle glass and clean it (this took oven cleaner and a razor blade on the one I had).
Take the middle of the door apart and expose the soft gasket (don't move it!). Clean out any broken glass and Insert your new glass. Put the middle piece of the door back on and line up all the screw holes! Put the first of the glass rails back on and the cleaned middle glass back in place, then the second glass rail. Put in the two screws that hold the glass rails.
Now you are ready to put the door back together. USE THE BOX TO HOLD THE DOOR OFF THE COUNTER WHILE YOU PUT THE HINGES BACK IN AND PUT THE DOOR FRONT BACK ON! If the screw holes don't all line up start the screws and work your way around, you'll get them to go in.
Voila! Door fixed.

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

Replaced the lower heating element with a new part.

cut power off and placed sturdy table same height as bottom of oven in front of oven. removed trim screws. pulled oven out onto table. removed top cover and panel on left side . tested transformer to be sure it was bad. then replaced transforner

My husband took the back off and replaced it. The repairman suggested pulling the range out into the floor to run the self clean mode. I have owned several such ranges and have never had to do that and won't now. Easy Clean Oven Cleaner will be the next thing I use.

I am not the handiest guy around so i was a little nervous doing this job but figured i would take a crack at it ( no pun intended). Took the door off as per instructions from kitchenaid , unscrewed all the outer screws , took off the back of door unscrewed the metal bar holding the glass in ( there are 3 levels of glass) took the 2 good glass sheets out got to the broken glass removed that put the new one in , replaced all the other glass and screws and put door back on, and i felt so proud. Probably saved about 150 dollars by doing it myself. I feel so proud.

Scarey> First thing you should do is cut off the electricity at the main breaker box. I dam near blowed myself up. It's 220Volt I found out after all hell blew up in my face. I was lucky and didn't get shocked.I shorted out the old broiler element.

So I made the job real easy I called a professional to come install the new broiler element.

I suggest you put a big red paper in each box that says turn off the power first. If your not sure how to do that call a pro.

This was more difficult than anticipated - probably because I'd never done it before. Once I got the door off (I didn't have the proper pins and used nails but didn't realize they had to be headless) I found all the screws, which were relatively easy to take out. I was surprised that the thermal door glass was obscured by two other panes of glass. It took more disassembly than anticipated and a few false starts when reassembling, but all in all it got done. I was happy that a job that would have cost probably $300 or more ended up getting done for $40 plus my labor - which isn't worth much these days. I'd certaily do it again.

Ordered a new one, put it in place in less than one minute.

The replacement turntable we received was an exact duplicate of the original. It was as easy as rinsing the new turntable, taking the old turntable out and putting the new one in.

The replacement of the blower was an easy repair. Just had to remove two back panels of the oven and the blower was then very accessable. Just remove the two electrical wires and then three screws and the blower came right off. Put the new blower on with the three screws and replaced the 10 or 12 screws holding the back panels and the job was complete!. The difficult part of the job was removing the combo unit from the cabinet to access the back panels. That part took some effort. Had to build a platform to slide the oven out onto after I disconnected the electrical feed wire (#6 wire) located in a junction box in my attic. Once that was done, the actual blower replacement was simple. The turntable motor was a different story...Although replacing the turntable motor was going to be as easy as replacing the blower motor, I couldn't access the underside of the microwave without disassembling the whole combo unit cabinet! That was very disappointing to me that Whirlpool didn't make that part easier to access, so I didn't replace the turntable motor. Too bad but we are just going to live with the turntable not turning!!

Part arrived in timely manner and placed it in microwave oven.