GS773LXSB0 Whirlpool Range - Instructions

Take off the back panel of stove and unplugged timer motor and switch on door latch assembly,removed two screws that hold assembly and slide rod off. I put 110 volt plug to timer motor and it did not move, that is how I diagnosed problem. Ordered new assembly (cannot buy just timer motor)put new door latch assembly on and worked fine. Of course unplug stove before you start !

I did the repair by myself. I used masking tape to hold the side trim in place. It was pretty easy and it looks great.

First make sure it is the gas valve not the ignitor. If the clicking sound still happens then the ignitor is fine, no clicking means ignitor may be broke and try to fix that first because it is cheaper. For us I knew it was the valve because the ignitor still clicked and the broil and top elements still worked. After the part arrived I turned off the gas and pulled the power to the oven. Disassembled all the components taking pictures along the way to remember what it looked like to go back together. Installed the new valve and use yellow gas tephlon tape at the seals. Put components back in reverse order. Run the top elements first to get gas in all the gas lines and remove the air. At this point the oven bakes again.

Took off the screws on the back of the stove and took out the sensor, and put in the new one.

Removed back of stove, 8 screws, removed original latch assembly and installed new assembly. One thing that can cause you difficulty is that the rod that connects the assembly to the front latch on the door can disconnect and has to be reconnected.[Problem]

removing the screws holding the burner together was impossible. they snapped off and I had to drill them out. that took the most time. after that it was 100% easy hookup. clean up of the burner was done with a wire brush. good quality products. thanks.

We needed a repair man to do the job because we did not have the tool to remove the screws on the burner heads. Also the on line diagram was not accurate. It actually was much simpler than showed in the diagram. Had we done the job, we would have done a lot of dismantling. The repair man removed the old top in a flash and the whole job took about 40 minutes. He knew what he was doing. Detailed instructions should come with the part so the do-it-yourselfer could figure out how to do the job.

take the 2 screws that hold the handle on out...watch the glass front and the side trims because the handle holds them on. Take the glass out then remove the side trims. Replace the side trims holding the glass in place with 2 pieces of masking tape om each side then install the handle with the 2 screws and remove the masking tape.

changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.

I remove bottom trim which is held on by 3 screws and try to install new bottom trim, did not work well. I then remove yop handle assem. Then the door glass which you need to clean after. Then install the new bottom trim then insert the glass into the new bottom strip using masking tape to hold the glass and side strips in place prior to installing the the top handle piece which is held on by two screws. Not a hard job to do.

The bake part of the oven was not igniting all the time . I checked the website and they don't list the igniter separately from the burner tube. This part is the exact fit for the igniter. There is no need to buy the whole kit if the igniter is all you need. it will fit right on the burner tube with no modification at all. Part number PS897264 is the igniter and burner tube. Part number PS898618 is just the ignitor.

Removed door per instructions in manual. Removed racks and storage drawer per manual. Removed two phillips head screws holding bottom pan and removed pan. Removed two phillips head screws holding igniter tube (#12) and withdrew tube from the cavity. Removed two phillips head screws holding igniter and bracket to the tube. Unplugged elcetrical connection to igniter and installed new igniter in reverse order. Too bad the igniter wasn't the problem.

This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The second one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.

Looked up on-line the error problem and what part I needed to fix it. Part arrived very quickly and everything was going fine until I realized the stove had two sensors. Replaced the top sensor now I am getting an error on the bottom sensor. Maybe I replaced the wrong one. I will replace the bottom sensor with the one I took out and see if that does the trick. Very very satisfied with PartsSelect. Good Price, Quick Shipping, Would do business with them again. They are now in my favorites so I can find them again if I need parts.

Install bottom door trim first...Remove upper door handle and set new glass door front piece in place and re install upper door handle and tighten all screws...Looks great