GS5SHAXNL00 Whirlpool Refrigerator - Instructions

Swapped out the emitter and receiver control boards. Super easy. Watched the video on how to do it on your website.

1) Turn off ice maker 2) Remove old filter by making 1/4 counterclockwise turn 3) Insert new filter and tighten 1/4 clockwise turn. 4) Turn ice maker back on 5) Press & hold "reset" button by utilization display to return to 99% - DONE !

I replaced broken fridge with a spare fridge; mean while I went online and did research and came across "Parts Select" which was extremely helpful with similiar situation and helpful guidance. $80 and fridge is as good as new.Thank you.

follow instructions on web site to install motor module.Great web site. Saved me a lot of money.

the tutorial is perfectwatch Steve. The boards were bad but coincidentaly so was the motor/control unit. I satrted with the boards, got my LED codes back to normal but still could not dispense. Installed the motor/control unit and had cubes dropping in 15 minutes. Great service, great tutorials.

fan motor housing had to be drilled through both sides of housing to attach to existing bracket. Possible damage to wiring inside the unit may disable condensor fan motor when motherboard is replaced. (Motherboard on order.)

installed new filter

I'm a 65 year old widow on a limited SS income, so I needed to get my refrigerator fixed as cheaply as possible. Partselect's troubleshooting guides took me right to the problem. I ordered the part on a Friday and it arrived the next Tuesday. It probably took me a little longer than it would a repairman, but I did it myself with just a screwdriver and a nut driver and it only cost me $45 instead of the $200 plus it costs my daughter to have someone else replace hers two years ago. Always remember to unplug amy electrical device before removing the covers or attempting any repair. All I had to do was remove the lower back cover on the refrigerator and, using the partselect diagram, locate the casing that covered the start relay and the overload switch on the left side of the compressor. I popped the casing off with the screwdriver, pulled the relay off (it's sits on two prongs), and remove the red terminal wire from the relay. Installation of the new relay is the reverse steps of the removal. Thanks, Partselect! I will be doing business with you again if the need ever arises.

Besides the refrigerator not cooling, there was a click-buzz-click noise occurring at the rear of the refrigerator every 5-10 minutes. I started by looking up the issue online, I determined the issue was either the compressor or the starter device. I ended up ordering the replcement starter device from partselect.com. The replacement was very easy. All I had to do was pull off the rear cardboard panel, unplug the wire bundle to the starter device, and pull out the starter device.

I watched the quick video once to see the type, if it matched mine, and the difficulty. I went ahead and ordered the part and within minutes, I had the ice maker installed. The video was so well designed, I only had to watch it once!

Removed pan from fridge. Removed shelf unit and placed on bath towel, upside down. Removed plastic slide rails from both left and right sides. Re-installed new rails (left and right were interchangeable). Put new installation back in fridge and slid pan back in. Super simple!!! A video was available on Partselect on the replacement parts page. ANYONE can do this!!! Thanks much Partselect!!! Brian

Ihis $2000.00 plus fridge's icemaker lasted only a few years. I saw on you tube a video showing what may be causing the problem. After ruling out any problem with the electric eye mechenism I figgured it had to be the actual icemaker itself. I purchased one ,it installed very easy and is now working fine.Had I known it would be this easy to diagnose and install I would have replaced it years ago.

A local appliance parts distributor suggested that I go on line to get help figuring out the problem. The motor assembly was 51% probability. I ordered the part and followed the instructions given at the time of purchase. In a very short time ice was dropping.

Just watch video from part select and following the instruction to replace the control and motor assembly.

I did exactly as the man on the video showed me to do. However, I was not sure what part was broke so I replace them both. Under $100 and my problem was fixed. This place had great shipping too: 2 days. They will be my first choice next time I have a problem. Oh and our local repair company would have been $125 for just a service call and they could get to it in a week.