GS440LEMT2 Whirlpool Range - Instructions

Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.

Took off the screws on the back of the stove and took out the sensor, and put in the new one.

Removed back of stove, 8 screws, removed original latch assembly and installed new assembly. One thing that can cause you difficulty is that the rod that connects the assembly to the front latch on the door can disconnect and has to be reconnected.[Problem]

removing the screws holding the burner together was impossible. they snapped off and I had to drill them out. that took the most time. after that it was 100% easy hookup. clean up of the burner was done with a wire brush. good quality products. thanks.

Very easy. A couple of screws and it was repaired. Parts select makes it easy and affordable to do minor repairs on my appliance. This is the second time we have used this company to repair our oven and so far all has gone very well.

We needed a repair man to do the job because we did not have the tool to remove the screws on the burner heads. Also the on line diagram was not accurate. It actually was much simpler than showed in the diagram. Had we done the job, we would have done a lot of dismantling. The repair man removed the old top in a flash and the whole job took about 40 minutes. He knew what he was doing. Detailed instructions should come with the part so the do-it-yourselfer could figure out how to do the job.

take the 2 screws that hold the handle on out...watch the glass front and the side trims because the handle holds them on. Take the glass out then remove the side trims. Replace the side trims holding the glass in place with 2 pieces of masking tape om each side then install the handle with the 2 screws and remove the masking tape.

changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.

The malfunction was narrowed down to the oven door motor lock, located at the upper left back of the unit. Removed two panels from the back of the unit, 8 screws. Then the motor, 2 screws, 4 wire connectors. Reversed the procedure for the installation, and solved the problem. About 30=35 minutes for the job. If your handy at all, it should not be a problem.

We took the door off and took it and the side panels to the local dealer and he put them on for us - for anyone needing to replace the side panels on the over, be aware they slide under the glass front -not over it like we tried to do. We thought, though, that we were going to have a buy a new stove but for a little over $70. 00 We got the parts, had them installed and saved over $800 on a new stove - well worth the effort.

Open oven door and remove racks. Remove 2 screws at back of oven floor and remove bottom plate. Unscrew screws that hold flame defuser. Remove defuser. Remove screws that hold bake igniter and flame tube. Unplug wire to bake igniter. Remove screws to bake igniter. Replace old igniter with new igniter. Replace screws and wire to igniter. Replace flame defuser and put screws back. Put bottom plate back into oven. Replace 2 screws at back. Replace racks. close door and test by setting thermostat to some temperature and verify that oven works.

The first thing you need to do is remove the racks from your oven.

Then look around at the back of your oven for the screws that hold the bottom pan down.

Remove those screws and remove the pan. Some need to slide back and then come up others will just pull up.

Remove the heat shield that is over the burner.

Remove the bottom drawer of your oven.

Now you should be able to see the igniter that sits on an angle by the burner tubes with a couple of wires coming out of it.

Removing the screws that hold the igniter is probably the most difficult part with some ovens. Sometimes it is easier to remove the whole bracket that holds the igniter and then remove and replace the igniter out of the oven.

The wires for the igniter will go to a Molex plug. Follow the wires and undo the plug. On many units it will be below the oven in the drawer opening at the top back. You will need to lay flat on the floor and reach back in to do this.

Once you have the old igniter out then you can carefully install the new one.

Check to make sure that you can feed the Molex plug and wires down through to the bottom before fastening the igniter.

Once the igniter is secured and the plug is connected, you can then replace the other parts in the reverse order that they came out.

This repair is only if your old igniters are working but they are so cracked that the spark is not going where it should be. TURN OF THE GAS SUPPLY VALVE BEHIND THE STOVE AND UNPLUG THE STOVE FROM THE WALL.I had to drill out most of the old screws to remove the burners plates because of all the old baked on spills. I bought replacement screws when I bought the igniters because I felt this would be a problem. My repair time included scrubbing the stove top. Once all the parts that make up the stovetop burners were removed (NOTE WHICH BURNER PLATE CAME FROM WHICH LOCATION, THEY ARE DIFFERENT SIZES) and I could see the pipes beneath the stove top, I cleared off the top and used a spreading knife to push in the clips on the left and right sides near the front of the stove. It was thin enough to fit in the space between the stove top and main body. Push the clip inward and pull up on the stove top and it will let you lift the top. Be careful because it may release suddenly so be gentle. I also removed the top section of the back of the stove to access the igniter terminal block. A few screws, nothing more. Be sure to take note of which wire goes where. (They are color coded). Unplug the old igniters. it is easiest to cut he old igniters off of the end of the wires and pull out three wires leaving only one. At the back left of the top of the stove there is a rectangle channel that the wires are running through. There is a clip that holds the wires loosely together. Remove the wires from that clip or the next part will be difficult. Run each of the new igniter wires through their respective holes in the stove top. BE CAREFUL NOT TO DAMAGE THE WIRE INSULATION IN ANY WAY. When you put the burner plates back on the igniters will be sandwiched in between the plate and the stove top. Using electrical tape, tape the connector ends of the new wires to the one remaining old wire. Gently pull the old wire through the rectangle channel, pulling from the back of the stove. Take your time so no damage occurs. Once the wires are pulled, plug them in to their respective terminals and place the wires in the loose clip. Make sure the new wires are not crossing the pipe openings where the burners are located. You can close the stove top and double check there are no wires across any of the burner openings. Re-assemble the burners and plug in the stove. DO NOT OPEN THE GAS VALVE. Turn on the stove and check to make sure the new igniters are working properly and sparking to the burner plate assemblies. You should see a controlled spark. Do not touch the burner plates or igniters or you will be shocked. If all are working then you may put the back cover on and open the gas valve. If none are working make sure the stove is plugged in. If some are working then check the connection on the terminal block and the wire insulation. If they are still not working then you've got bigger fish to fry. Good luck my friend. Happy fixing!

I used the allen wrenches to block the hinges, removed the oven door and used the kitchen counter for a work station. I removed the trim piece at the bottom which released the side trim and oven glass front, and then reversed the procedure. It took more time to clean things than to do the exchange. My only issue is with Fed Ex who delived the first trim piece bent in the middle inside a crushed box. Part Select had another part sent the same day after I called them.

The replacement proceeds similarly as for electric range switch replacements described here, only this model is a gas range. The top panel does not lift up because of the feeds to the gas burners. It is possible, using a thin blade, to depress the spring fingers holding the switch in the oven panel, or else to remove it destructively. Be careful not to pull the old switch out too far, or else the wires will pull off the switch connectors and fall inside the oven-side panel cavity. This happened to me. The wires are very short. Another 1/2 inch of wire would have made all the difference. If this happens you have to fish out the loose wire. I gave up on this and took off the back panel (about 8 screws) and then loosened the bottom and sides of the side panel. This allowed me to retrieve the short wire and connect it to the back of the switch while pushing the switch into its mounting hole. Reattach the side panel, the back panel, and slide the stove back into place, and you should be good to go.