GS440LEMB3 Whirlpool Range - Instructions

Found that the two screws securing the bottom had rusted away allowing me to just lift the old bottom out. The new one fit in place exactly and really did not need the screws. Done in 2 minutes.

First I removed the gas line from th wall. Second I removed to gas lines going from the regulator to the stove. The regulator then unscrewed from the stove itself and that was it. I reversed the process to install the regulator.

My husband had no problem at all with the replacement of the exterior glass.
Slipped it in and attached to hooks and secured with the handle with a screw driver. Be sure to remember the trim doesn't cover the glass it kind of sits behind it. It can be deceiving in a way you may think in sits in front of the glass. Otherwise it was quite easy and the part came quickly in less than 24 hours....this is a great site.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

On the back of the range was a little plastic bag with the range document. In this document was instructions on how to check out the electronic controls, a drawing of the electrical wiring and a digram of the gas line part of the range. First I did the electronic part and it check fine. Following that the instruction was to check out the solenoid coils for the bake and broil valve. I believe the wires were blue, red and orange(it tells on the wiring diagram). It called for 216 ohms on each coil. When I unpluged the plug from the circuit board on the upper right backside of control panel I checked the resistance for the two coils. One side had 198 ohms and the other coil had 0 ohms. The instruction said that if either coil didn't measure 216 ohms or close to that value the valve would not work. So, I wrote down the Model number. Next I checked the gas valve for numbers, wrote down all that was on the valve because I didn't know which one was the part number for the valve. Went on line to the Whirlpool site, once in the Whirlpool site I found out they have a diagram of parts for different appliances, pulled up the model I was looking for, found the valve( under the valve part, the number was different than the one I had, but the information said it would fit the model of appliance I have) order the part. In a few days the part arrived. I turn the gas off, unplugged the electric. I removed the gas lines, had just a bit of a problem with the short gas line going to the burner for the oven, when the line was out I unplugged the control wires. Nake sure you write down how thw wires are on the valve before unplugging. There is an adaptor on the valve to the main gas line. You need to take this off and put on the new valve. This is where you need the pipe cement. Stay back from the end of the adaptor that goes into the valve one or two threads with the pipe cement. you do not want to get any inside of the valve. Put the adaptor on, tighten, plug in the control wires, replace the valve on the stove, connect the gas lines, put all the gas lines on before you tighten them. Turn on the gas. Check lines with soapy water for gas leaks. Plug in the electric, check it out. Don't forget to put the instruction back in their little plastic package and I also put a copy of the order I had for the new valve just in case I need it in the furture.

Removed bottom panel. Unscrewed igniter. Replaced igniter. Reinstalled panel. Started oven before replacing panel. Easy install.

I took out the two screws that held the oven handle in place inserted the glass in the door and replaced the two screw!!! That easy!

Simply removed three screws that held the door trim in place. Once the screws are removed be carefull because the front door glass is held in place by the bottom door trim. Otherwise an extremely easy repair.

Un-screwed 4 screws. Got part numbers off of the pieces. Put numbers in blank on web site and ordered the pieces. Parts cam in 4 days later and installed the pieces with my trusty screwdriver.

I have removed this piece once before and painted it,
but it is difficult to prepare surface.

I tried to replace the part without removing the door
but had difficulty getting the screws to line up.

So, I took the door off. Forgot that you are supposed to jam
the spring hinges in the open position before you remove the door. Manual describes how to do this but picture is not very helpful. So I made two wooden dowels about 3/8" in dia by about 3/4" long. Opened the hinge with a screwdriver and jammed the dowels in place.

Door Trim went on easily and the oven door went back on quickly.

Surprised they don't make this trim piece with rust proof material.

Removed the old, broken drawer glide by removing the Phillips head screw. Then placed the new glide into place and fastened with the existing screw.

The rivet on the top of the bottom drawer front was missing. I lined up the drawer front with the supporting bracket behind it and inserted the rivet. All you have to do is tap the top of the pin in the center of the rivet to lock it in place. No rivet tool is needed. That should be explained in the parts listing because I bought the rivet tool before I realized I didn't need it.

Remove 2 screws holding oven bottom in place.Lift out the plate and replace with new plate. The hardest part of the replacement was lining up the screw holes. By the way i have never received such great service from any internet company as Part Select. I ordered the part on a Monday and the part was at my home the NEXT DAY and installed that evening.

It was easy to find the part. I ordered it on Sunday and it arrived Wednesday. A stress-free experience.

Bought new igniter.
Pulled stove from wall and turned off gas and disconnected power cord.
Removed oven racks.
Removed oven floor.
Removed heat shield/dissipater thing.
Removed 2 screws holding igniter to gas burner tube.
Disconnected the wire (this was harder than expected because igniter had only a few inches slack in the wires), took off back to try to find better access to wires, no help there, door was not easily removable so difficult to reach in with 2 hands to pull wires apart, eventually I got it.
Connected new wires.
Replaced igniter to feeder tube with 2 screws.
Plugged back in, turned gas back on and tested.
Reassembled heat shield thing, oven floor, racks.
Done.

Unsrewed what was left of the trim and oven handle. Just 4 screws total, then replaced the 2 screws of the trim and the 2 screws on handle.
Finished! Replacement parts fit perfect!!! Thanks a milliion!