GS2726CEHQ Maytag Refrigerator - Instructions

I removed the ice maker from the refrigerator, by removing one screw on the underside bracket and loosening the two screws at the top side, then lifting the ice maker off the loosened screws. I then unplugged the electrical harness that supplies power from the refrigerator to the ice maker. I then disassembled the ice maker by removing the front cover which is snapped in place, then removing two recessed screws at the front. I removed the broken part, I then reassembled the ice maker with the new part. I replaced the two recessed screws at the front and snapped on the cover. Then I reinstalled the ice maker in the refrigator by plugging in the harness, slipping the ice maker over the loosened screws in the refrigerator and replacing the screw that was removed from the underside bracket. Tightening all the screws completed the project.

I replaced the actuator switch and rubber pad with the switch actuator.
I had attempted to repair previously without replacing the pad but the problem continued. I put up with the problem for a long time waiting for the opportunity to get to the appliance parts store but their hours are hard to deal with and work myself. I was able to find the part easily with the on-line catalog and parts diagram and ordering was no hassle at all. Shipping was extremely fast.
I remove the front panel by removing the drip tray and the 2 screws at the bottom. Then gently lift up on the front cover assembly (careful with the connector to the circuit board at the top) it slides over 2 screw heads at the top. Remove all the screws that secure the dispenser to the fridge, one screw is hidden on the right side (as you face the front. Work the dispenser out and careful of the water tube coming from the top - it stays in place. The wire connector must be unplugged from the left side in order to remove the assembly and not actuate the dispenser while working (a good idea to unplug the fridge). A small phillips screw holds the switch in place and the actuator fits over with the slots fitting over lugs on the assembly. Reinstall as you removed - be careful to be sure all wires go back into the proper location and "tracks" to keep them out of the way and avoid pinching (if the actuator will not go back flush in its location check the wires to the switch).
Plug all wires bach in and don't forget the harness to the top of the circuit board on the front panel.
Plug back in and check your work.
Important to replace the actuator pad - its "elasticity" is the return mechanism for the switch actuator. Probably the issue I had after replacing the switch and still suffering the same problem.
Good Luck!

First I unpluged the refrigerator, then I removed the drip shelf (slides out). Then removed the two screws hidden by the drip shelf. Then I removed the control panel by pulling out on the bottom then lifting slightly to to expose the ribbon cable. The circuit boards you see at this point will deliver an electrical shock if the refrigerator is plugged in. I disconnected the ribbon cable form the control (front) panel. Next I removed three screws that hold the chute assembly in place and worked the chute away from the door. Pay attention to the placement of the water line before you remove the chute. The bad flap fell out at this point but it is easy to fiqure out how to place the new one. When putting the chute back in place make sure the arm holding the flap is aligned in the groove of the solenoid plunger and not just setting on top. (I had to do this twice because the chute would not open the first time I put it back together). About a 30 min job because I took it apart the first time to see what was broken. I only needed the flap, the arm it mounts to an the solenoid were not broken. Easy to do and only cost about $16.00 with shipping for the part.

The easiest thing to do was pull the ice make off. After taking the 3 screws out of the wall of the freezer, take a screwdriver (flathead) and push on the tab for the electrical plug and wiggle the cord out. Then you can take 3 screws out for the main cover and another 2 screws on the next cover. There's the part, pop it out and replace holding pins and start the process of putting back together the opposite way you took it apart.

The ice maker was not getting water. I hotwired the water valve by switching the connectors for the water dispenser and ice maker water valves and water flowed into the icemaker when the water dispenser lever was pushed. I wronly assumed the water valve was good. I removed the icemaker and determined that the gear motor was not getting power in the position the icemaker had stopped.In this position, the thermostat determines when the motor gets power so I replaced the thermostat. The icemaker still would not get water! As it turns out, the water solenoid was sticking due to a deteriorated rubber washer which let the solenoid plunger get too far out of the magnetic field. I replaced the water solenoid assy and all is well. Don't get fooled by hotwiring the valve. If it isn't getting water, the solenoid probably is the culprit.

Quiet a simple repair. First I removed the ice maker bin and the plastic side panel on the right hand side. From there, I was able to remove the ICE ENCLOSURE . It unhooks. Next I removed the ICE DESPENSOR ENGAGEMENT YOKE. It has reverse threads so be careful. Next I removed the ICE AUGER MOTOR. Its located at the back of the ICE ENCLOSURE and held in place by 4 phillips screws. You also need to remove the SOLENOID YOKE ASSEMBLY which is located just to the left of the ICE AUGER MOTOR. It unscrews with 2 phillips screws. Next I reassembled the ICE AUGER MOTOR and SOLENOID YOKE ASSEMBLY to the new ICE ENCLOSURE. Then I reinstalled the ENGAGEMENT YOKE and snapped the unit back in place.

Perhaps a helpful hint:

When aI received the hose adapter/connector, I inserted the 2 hose ends only to have water drip from the connection.
I used a utility knife to remove an inch from each side, then reinserted the hoses. That made the differnce. Dry as a bone.

LG

The tiny piece of plastic that holds the wire that shuts off the icemaker, broke early on with our fridge (after just a few months.) We superglued it, but last week it bit the dust for good.

Once I got this part, I removed the freezer door and trays, and pulled the icemaker out by removing 3 flathead screws and unplugging the cables. Laying in the freezer on the floor was a bit unconfortable, but not too bad.

Then I inspected the icemaker. There was no obvious way to remove the part without disassembling the front of the unit (where the motor is) to release the spindle and free the part, so I did that - 3 or 4 nuts was all that held it together. Once that was out, I removed the spindle, swapped out the part, and put it all back together and back in the freezer. Plugged it in and waited.

It took a while to start making ice. Like 5 hours. Now it's going pretty slow (much slower than before.) Haven't had time to look into it, but my suspicion is the rubber hose that feeds water into the icemaker is blocked with ice or kinked. In any case, we have ice now (but not a lot), and the unit shuts itself off properly. However, we went from having too much ice (thing never shut off) to too little (thing makes ice too slow), so I need to shoot for somewhere in the middle ;)

I noticed that the thin plastic flap was missing. I squeezed the housing, unsnapped and pulled. INstalling the new part was just the reverse. No more frozen vegetables.

Ice door flap was broken and warm air was getting into the freezer. I removed a total of 4 screws to get to the flap. Total time was less than 15 minutes and very easy. Partselect customer service was very helpful and friendly. If you have any questions, do not hesitate to call them. They were very helpful! I have this site bookmarked!

I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!

I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt

first i remove the two screws like the guy said on your web site. then i pulled the cover off with a upward motion revealing three more screws witch i removed. I then removed the dispencer. unpluged the wires and removed the switch and pad and replaced with new parts.I reinstalled the wires then the unit, installed the screws and cover.Checked for proper operation.Then enjoyed that cold beer! Thanks to your wed site and repair info. I saved at least 100 buck to the repair man. Thanks Partselect.com

I read many reviews on how to change the seal/gasket, and decided that as I was the only one around to do the job, it would be easier to take the fridge door off and then lay it flat. remember to take the handle off as well. Then it was a case of taking each screw of, there are many to remove. While this job was being completed, I placed the new gasket in hot water from the tap to soften the gasket as it came in a box folded. Once all the screws were removed , then it was a case of fitting on the new gasket starting from top and working my way around. finally placing all the screws back, but not too tight. Then I placed the door back and also placed a flash light in the fridge to see if any light was coming out. The door opened and closed without any problems and the seal did not have any gaps. finally with door on the fridge, I tightened the screws-only hand tight. Job completed. This may sound obvious, but any way, dont forget to disconnect the fridge from the electrical supply, otherwise you risk burning out the motor, with all the extra work the fridge has to do, while you are doing the replacement.

I first removed the tray at the bottom of the Ice/water compartment, 2nd, removed the 2 star headed screws that are visible and 1 star screw near the water hose. removed front pannel. 3rd removed 4 star screws holding ice/water assembly, let this hang down and was able to reach in and removed the round broken shut door. replaced with new door, Difficult to get new door in but I was lucky and got both side wings in the proper slots. Did everything from above in reverse. New Ice doot works great. I just wish you had sent some type of instructions! Very happy with your company. Other web sites wanted me to buy a complete kit just to get the door assembly. you saved me $30. Thanks