Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
non-functioning refrigerator lite switch
My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate (manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close door and plug back in. Open door to check that the lite works. Walla! It did. Thanks!
First we ordered a new solenoid. . . The little piece that opens and closes whenever you push the button to dispense ice. That definitely needed to be replaced, and it was easy to do. However, that didn't fix the problem, so we looked and looked at the assembly and decided that a spring was missing. We ordered the spring, and when it arrived, we found that it matched exactly one that was already on the assembly. :-) Not the problem. Thirty minutes later we figured it out,. The diagrams at part select were not helpful with this. It was a matter of figuring out how the magnetic weight fit into the assembly. That's all it was! Now we have an extra spring for the future.
Remove 2 screws, and GENTLY remove tray. There are two motors on the back side that are wired in to the back of the fridge. Unplug the harness and the whole assembly will come out. Take note of the way the plunger comes out, if not, it will take a little more time to figure out. reassemble motors onto new tray then GENTLY slide into postion, with one hand plug in wiring harness then seat tray into position and reinstall screws. Done.
Used screw driver to pop out old switch. Used pliers to hold wire connection from fall back into slot on fridge. Inserted new swith into plug and pressed new switch back in place.
Ice maker auger wouldn't rotate, motor worked fine
To replace the broken drive coupling on the motor end of the auger requires sliding the ice bin out of the freezer section of the refrigerator. Remove the ice cubes and let it thaw out for a few minutes. Remove five screws holding the front face on the ice bin to remove the ice auger. slip the new drive coupling over the end of the auger. reassemble and replace the face plate with the five screws. Slide the ice bin back in the freezer. Less than fifteen minutes it was finished.
Ref door would not close properly causing excess condensation... This in turn caused water to leak under door and rusted the door hinge.
Simply remove the ref door bracket at top and remove the door from the bottom hinge pin...Then replace the lower hinge, hinge pin and door closer... Reinstall the door and adjust for level...This took only 25 min to fix.
Ice Stripper was broke off, leaving the mounting tabs still inside their respected spaces in the ice-maker
Had to remove the ice-maker (also easier than trying to work inside the freezer letting all the cold air out). A few mounting screws and an electrical connection in the back. After it was out you will need to remove the cover (not the superficial cover that just pries off) where the gear is behind it, just far enough so you can get the mounting tabs on the ice-stripper in. In order to to move this cover out, after removing the screws (the obvious), you'll need needle nose pliers to ever so slightly squeeze the plastic clips together that hold the plastic movable bracket and the metal ice level arm/switch, so it will pop out. Once you have room to put the ice stripper in, it should just all snap back together, then proceed in reverse to put it all back together.
Called a serviceman. The Air return cover is NOT the cover we replaced. Ours is 3/4 of the way down on the freezer side of fridge. Put a thermometer inside, to monitor it.
Light Switch Was Faulty--Failed A Few Months After Purchase Of The Refrigerator
I had several times tried to get the old switch out but with no success. Ordered the "repair kit" and followed directions for removing old switch (there is a plastic spring clip on one side). Easy to unplug the old switch, plug the leads into the new one, snap the new one into place. Took about 5 minutes total--piece of cake. I wish I'd thought to try this years ago when the old switch began to fail.
Had to completely remove the ice maker in order to install the replacement part
Sorry for delay in writing. Part I ordered arrived two days ago and it was exactly what I needed. Knowing that there will be problems even with the smallest job I procrastinated starting. When I did start this morning I foud I had to completely remove the ice maker and disassemble it in order to install the water fill cup bracket. The challenge was reassembling the unit. Not hard for an experienced repairman but a challenge for layman. Everything is thing is back to gether now and power on cooling down the refrigerator. Won't know how successful it was until turn on water and ice is formed. If it works this saved $75 just to get a Sears repairman to come out and tell me what would be needed to fix the refrigerator and $1,000 if I had to buy a new refrigerator. Extremely satisfied with service I received. Thank you.
I used a knife blade to slip under the edge of old switch to pray it out of the hole it was inserted into, switched the wires and replaced the new switch into the same hole. It took about five minutes!
