GR465LXLS1 Whirlpool Range - Instructions

After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.

I ordered the part, which only took a very short time.
Then I repaced the part.
Worked like a charm

switched out latch asy,rear

Easy repair with Phillips screw driver and needle nose pliers. 1. Turn off Breakers or unplug range, Open oven door and remove the two screws holding the glass top to the oven frame. 2. Slide glass top forward and remove the two electrical connectors at the rear of the glass top, one on each side. 3. Remove the Phillips screw holding the ground wire from the rear top flange of the glass top. 4. Glass top can now be removed and placed glass side down on a padded flat table top. 5. Take a few pictures of the wiring and brackets for reassembly reference. 6. Remove the 4 wires from the defective heating element with needle nose pliers (note locations for reassembly to the new element) 7. Remove the Phillips screw on the rear side of the bracket holding the defective element. Carefully lift off the bracket. 8. Heating element can now be removed. 9. Remove the locating flanges from the defective element and install on the new element in the same locations. Clean glass if necessary and place new element on glass. 10. Carefully locate the flange tangs into the same holes on the bracket, reference photos or other side for locations. Ensure small element bracket was replaced in mounting slot of large bracket and reattach bracket screw. 11. Replace wires to same locations, remove and lightly pinch connectors if they appear loose, then reassemble. 12. Replace glass top on range, reconnect the two electrical connectors and ground wire, slide forward and replace the two mounting screws. 13. Restore power and check new element for function. Extension wires which came with the new element were not needed in this application. Total repair time about 20 min.

After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

ordered new front and replaced

I had some confusion about the correct series number associated with my stove and called Partselect. They confirmed the part I was looking at was correct in less than 5 minutes. I then completed the order online. Even with standard shipping my order was processed immediately and I received the heating element the next day.

Turned off the breaker. Removed the two screws in the front holding the range top down. Loosened the screws holding the element in place while balancing the range top with my shoulder. Removed the wires from the older element one at a time and attached them to the new element. Put the new element in place and screwed back in place. If I had a little help with the range top I think I could have completed it in 5 minutes but I was at home alone and the other stories of doing this repair made it seem easy enough and it was.

Slide range out,unplug range,remove rear cover to unplug element wires, open door remove screws inside oven remove element

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

It was simple. Unscrewed to screws at the back of the oven. Slipped off the wire connectors then attached the wire connectors to the new part, put the screws back in and we were back in business.

removed the two screws that held the cook top on and moved it enough to get to the light switch. Removed the switch and tested with multimeter. Pulled the two wires out of the mounting hole and insulated with elect. tape. Replaced the cook top and installed the two screws that hold it in place. Located the switch at PartSelect on line and ordered it. When the switch came in (the next day), I connected the two wires, and snapped the switch in place, and I was back in business.

looked for how to video on you tube. It saved me lots of money. Anyone could do it.

Removed the two screws holding the remaining pieces of the old handle - screwed in the new handle.

Had this range for 6 years. My daughter turned on the burner and it went "pop". She was very upset. I found the best price at PartSelect, and ordered the same day.

the first burner arrived broken in the box. We contacted PartSelect, and they immediately sent another and rushed shipping. It arrived in excellent condition.

To replace the unit: First, I turned off the circuit breaker for the range. Then I removed the two Philips screws that held the cooktop down. Next I removed the nut screws holding the burner to the cooktop.

Then I placed the new burner next to the old one, and one by one swapped the wires (this way I was sure I had the right wire on the right connector). One of the wire connectors broke when removing it from the old burner. PartSelect had provided 4 repacement connector pieces (oddly, all of which were too small for the burner element). So I located a replacement connector at a local hardware store. Stripped the end of the wire and used pliers to fasten the new connector.

After all connectors were secured to the new burner, I screwed the burner to the cooktop, then closed the cooktop and secured it with the two screws.

Turned on the circuit breaker, and it works like new! Saved over $100 by doing it myself!

See description listed as problem