GLS3074VS01 Whirlpool Cooktop - Instructions

The only real issue was locating the proper adhesive to ensure that the new pads would not fall out. The small insert paper slip in the package noted that a RTV adhesive should be used. After much searching at the home improvement super store, I learned it would be found at an auto supply store. It is black, and is for high temp use. It is available in a small tube for around $2.00. The RTV is usually used to make gaskets for heat/oil exposure in auto repair. I did have trouble removing a broken stub from a pad that had broken off in the hole. I used an awl to get what I could and push the rest into the hole deeper, then insert a new pad with along with the adhesive.

My husband and I replaced the igniter module, following directions we found online. We removed the old one, replaced it with the new one, and thankfully everything is working great!

I had to remove the two separate components of the gas burner unit, each had two screws. I lifted then tilted the lower portion of the burner unit to allow access to the underside of the igniter. I removed the wire and then with an offset screwdriver I removed the single screw that held the igniter in place. I reversed the steps to install the replacement, very quick fix.

I was also very pleased with how quickly the order was processed and the part was delivered, only three or four days with standard shipping.

I went online and discovered the repair method and schematic of the range. I removed the spark module after first removing the upper rear panel cover and replaced with the new part module ordered from your company and now the spark module operates all the gas elements when they are turned on thus lighting the gas burners. My mother in law was thrilled, as she had been using matches and burning her finger tips,since the original range part malfunctioned. The only problem was the small screw from the original installation was not long enough , so it required some changes to get it affixed to the cabinet side.Thanks for the reasonable price and the right part for the job!!

I just put the grate pads in the bottom of the grate. The repair was a snap.

Original bumper pads NOT glued into the burner grates. Hence they began to disappear during routine use and cleaning. Very simple repair with a little glue this time around. But fairly expensive for a very small part set

Removed back upper cover, unscrewed retaining screw from module. As noted in a comment from another do-it-yourselfer, I replaced screw with a longer one and reinstalled module. Note that the replacement part is not exactly the same as the old one(the wires are located differently), I noted the wire color codes with the slot number and reinstalled them in the same slot number. Works fine.

We replaced the part. It was pretty quick and easy to install.

Replace igniters

Been looking for grate pads for 10 years and finally found you site and part # WPL 814323.
Wasn't sure that they would fit but couldn't even find new grates so decide to try them --Fit perfect.
Kitchen aide stove top gas with round grates. Used the drill to clean out the holes with broken pads still embedded.With clean holes the new pads just screwed in like the originals. Thank you very much

cleaned out pad area with an awl. then the pads just slide in.

Remove the screw on the front of each side, also there are two screws holding the burner controls. Remove the burner knobs. There are two screws holding the burner head to the top of the burner panel, looking down on the burner head, these will not come out easily. Here's where the drill comes in. Drill the two screws head off, there are two gas line connections that must be removed, be careful not to twist the gas line. Remove the burner head and replace with the new one. When replacing the burner head, screw the gas line to the burner head first, then to the main gas control.

1. Turn off Gas at valve under cooktop. Unplug electric to igniters. 2. Remove all control knobs. 3. Remove grates and burner covers. 4. Remove screws from each burner head (10 screws) 5. lift and remove cooktop cover. 6. Reach under cabinet and push up main cooktop body (about 4 or 5 inches) and BLOCK. 7. AT FRONT OF COOKTOP REMOVE 2 philips screws holding burner strip. Slightly lift burner strip enough to get short handle philips under screw holding igniter (Be gentle as gas line is still connect and will give enough so as not to have to disconnect them. 8. Remove and replace igniter. 9. Reverse procedures above.

Simply remove two screws take old one off and line up and put new one on and replace the two screws. Couldn't have been easier.

remove grate - flip upside down - be sure holes are clean and dry - using toothpick, swab some RTV sealant into the holes and a bit on the pads ... insert pads till they seat - be sure to hold in place till all air is evacuated - wipe excess RTV with paper towel...DONE