Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
Below is a list of all parts for the Frigidaire Dryer GLER341AS2 - Residential. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.
This rear drum bearing kit is designed for use with dryers. It supports the rear of the drum in your appliance as it tumbles your clothes during the drying cycle. If your drum will...
This drum belt, often referred to as a drive belt, is used in the assembly of dryers. It goes around the drum, the idler pulley, and the motor pulley. As the armature on the motor spins, this belt is what rotates the drum and tumbles your clothes during the dry cycle. If you can hear the motor running but the drum is not moving that is a sign your belt is broken, stretched, or damaged, and can no longer grip the drum. This belt is 87 3/4 inches long, and is 1/4 inch wide. Because it is made of rubber it is common for this part to become brittle and need to be replaced. This is an authentic OEM replacement part, and it is sold individually. Remember to unplug your dryer before you begin repair work.
This selector knob may also be known as the laundry appliance control knob and is meant for your washer or dryer. This model is sold individually and takes a D-shaped shaft. The pu...
This white drum glide is used in a clothes dryer to ensure the front of the dryer drum is supported as it does rotations. *Please note: these are sold individually, however there are two of these in your appliance. We recommend that these be replaced at the same time, this allows for optimal performance and ensures they wear evenly. Each drum glide is approximately 33 inches in length. If the following symptoms occur, consider replacing the drum guide as a solution: dryer is noisy, will not tumble, or leaves marks on clothes. Remember to unplug the power source to the dryer before installing this part. Refer to the diagram provided by the manufacturer for further instructions and guidance.
If your dryer does not tumble, will not start, is noisy, or is leaving marks on your clothing, you may need to replace the drum support bearing. The drum is supported at the rear b...
This dryer heating element produces heat to dry clothes and is located in the rear of a dryer. If the heater element is burned, the dryer does not heat or over heats, or clothes are taking too long to dry, replacing this part could solve your problem. The tools needed for this repair project are a Phillips screwdriver, putty knife, and needle nose pliers. To repair, first remove the main top of the dryer and ground strap at the rear. Disconnect the two wire harnesses and remove the screws that hold the front panel to the cabinet, in order to pull out the front panel. Now that you have access to the inside of the dryer, refer to the manual for further installation instructions and detailed guidance. Remember to unplug your appliance from the power source before beginning this repair project.
The dryer thermal limiter, also known as a thermal fuse, blows the fuse to cut off power to the dryer when the dryer begins to overheat. Once the dryer reached 220 degrees Fahrenhe...
The door catch on your dryer is an important part as it keeps your dryer door closed, in order to ensure no air or clothes can escape. This part works by holding the door strike, which allows the door to stay secure. Before you begin this repair make sure to disconnect the power supply to the dryer. The tools you will need for this installation include a Phillips screwdriver and a small flat blade screwdriver. A pair of pliers may also come in handy. Users ranked this repair as easy, and say that it will take fifteen minutes or less to complete.
This part is used to start the dryer once you have selected a setting on the timer.
Located at the front of the dryer, this lint filter traps lint and debris from the exhaust air flowing out of the dryer drum. This part measures approximately 12 inches long x 7 in...
This high limit thermostat is used in a dryer and monitors the temperature to make sure it does not exceed 260 degrees Fahrenheit. When your dryer temperature reaches 260 it will cut it out and only comes back when it drops by at least 70 degrees Fahrenheit. If your dryer is overheating, taking too long to dry clothes, or is not producing enough heat, replacing the thermostat could be the solution to your problem. The tools needed for this part are a Phillips screwdriver, putty knife, and needle nose pliers. Refer to the manual provided by the manufacturer for installation instructions and guidance.
This ball hitch provides support to the drum located at the back wall of the dryer. This allows the drum to spin. The bearing may have gone bad and you might notice that the ball is cut off. The ball hitch might need to be replaced if you notice that your dryer is extra noisy, is not tumbling properly, or will not start at all. The ball hitch is made of metal and measures 5 inches in diameter. This is an OEM part that is sourced directly from the manufacturer.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.