GLEQ2152ES1 Frigidaire Dryer - Instructions

I followed the great instructions that were provided by Partselect. There were no surprises. I took my time and it now works like new.

disconnected the dryer; cleaned the duct. I reconnected everything and started it up again and within seconds tripped the breaker.Decided probably the thermal limiter was faulty, so ordered new one from you. After it arrived I watched video, then removed the top and front, pulled drum to give me some workroom, replaced the limiter, reassembled in reverse order.I then reset the breaker, plugged the dryer in. Runs perfect.The drum was a challenge - so I used a wooden wedge to support from the front and opened the 12 by 12 rear port to access and reset the pulley cable assembly.

removed two screws and installed new handle

I wanted to know why my dryer was making such an ear-piercing screech. Googled, and found Steve at PartSelect. After watching the 10 minute video on how to replace the rear drum bearing, I knew this was something we could do at home. I ordered the parts on Friday and they arrived on Monday. Also ordered a new drum belt and drum glide. Didn't know if we would need those parts, but figured while we had the dryer apart, we might as well replace them. My husband watched the 10 minute video the following Saturday, and together we replaced all 3 parts. The original bearing was small enough to fit through the hole (which it shouldn't) and metal shavings we all over the plastic holder. The large metal ball attached to the dryer had grooves worn into it. The kids we amazed, too! I can't believe the repair was so easy! Seeing the inside of the dryer makes me wonder why they cost so much! Do not hesitate to make this repair yourself. Even just one person could do it.

Follow instructions all most to the letter. In video it was stated to get an assistant to hold static / housing retainer in place to start screws. I put it in place and, used Duck Tape to hold it there while i started screws. Thanks for the deal on parts and, video. I would also suggest advising to check the nylon strips on felt at the front top. Mine were worn. But there was enough at the back of nylon to remove and, glue remainder in place almost as good as new. Again! ''THANKS!''

I remove the drum, and install the bearing just like the instructions in the video.

I researched possible causes on line and watched a PartsSelect video on YouTube on how to test. I ended up misreading test results and ordered the High Limit Thermostat but subsequently realized problem was the Terminal Block. No problem, PartsSelect took back the Thermostat (I hadn't installed it) and shipped me the Terminal Block. My dryer was back up and running in less than 7 days from initial analysis to installation of Terminal Block. Instructions that came in confirmation email for installation were perfect and easy to follow. Total cost with new power cord from Home Depot was less than $50 vs a quoted service call of $175+ parts from local electrician.

I watched the repair video on how to replace the rear bearing and ordered the parts.The video was 100% correct and showed the repair step by step I didnt even need to replay it.The repair went as expected and no left oover parts. My dryer runs smooth and quiet, My wife loves her quiet dryer.

i followed the video step by step & i never thought a repair could go so well thanks to the repair video

Watched video on you tube went to PartSelect web site determined it was the rear bearing from the probable causes listed. Received part in two days and the job took less than thirty minutes. The limited access to the belt motor was the only difficult part of the job but by putting the belt on the idler pulley first and pulling down on the belt I was able to get it over the motor pulley. Thanks PartSelect for making this job easier than I thought it would be.

remove 2 screws rear of drier at top slid the top back and off removed 4 screws on front electronic read out panel and disconnected two wire harness plugs remove the panel removed 2 screws for lower panel at top on either side of rotating drum,tilted machine back removed two screws at very bottom on front of dryer to remove lower panel ,and remove the lower 2 screws to remove front panel.lifted rotating drum up and out of drier ,removed 4 wires on the heating element and four retaining screws from rear of drier to releases the heating element,than reverse the procedure for assembly.

Installed both upper and lower felt to center drum in dryer housing

After figuring out how to remove the top, front, and control panel from the Gallery series, which is different than the dryer in the video, the repair was easy. Just followed the rest of the proceedure in the video.

The video was very helpful. Glad I bought the entire kit. Dryer works great and no noise.

Followed video that was provided!! Now I know how to get the top and front of dryer OPEN. Now I can clean interior of dryer ALSO, lots of lent!!