Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Lower rack wheel was melted
Unsnapped clip,and moved it 90 degrees. Slip wheel and clip off. Installed clip on new wheel. replaced new wheel. The wheel did not come with a new clip and was not suggested on the parts list. The existing clip was still OK but if it was not, I would have had to order a clip and wait. All in all, a good experience.
The wheels came with a clip on part that clipped to the rack and the wheel snapped into that clip. I am a woman and it was easy for me to do. Thanks to Parts Select for being an easy to use and navigate site, for quick shipment and for good directions with the parts. Sincerely, Teresa from Alabama.
Washing machine would cease functioning at the spin cycle and would not drain.
Remove the front coverfrom the machine. This is done by removing the 3 screws at the bottom of the panel. The panel then drops down and pulls straight off. The pump is located on the front right wall of the of the machine. You will notice a 2-3 inch diamete threaded cap on the right side of the front wall of the machine. This is the front of the pump and access to the filter. Place a large bucket under this cap and slowly loosen the cap. All of the water remaining in the machine will begin to drain (this could be a lot of water. Do not remove the cap completely so that you can quickly stop the flow of water if needed). Once all water is drained from the appliance, Disconnect the two hoses from the pump using a pair of pliers to looses the presure clamps, sliding the clamps back an then pulling off the hoses (be careful of any remaining water in the hoses). Then remove the two screws from the rear base of the pump that secure it to the bottom floor panel of the washer. Slide the pump slightly to the rear to free it from the fittings on the front wall of the machine and the lift the pump up. At this point, firmly pull out the wiring harness plugged into the top right side of the pump. Install the new pump by plugging in the wiring harness and resecuring the pump. Plug in the machine and run on the rinse and spin cycle to test.
Diswasher wasn't cleaning the dishs because the spray arms were clogged with calcium deposits.
Replacement of the arms is very simple, the bottom arm pulls out after turning it counter clockwise, no tool needed. The upper arms need the use of a nut driver or simlar tool to remove the hex screws holding them to the water supply tubes. The hardest part of the repair will be removing the top dish tray. This requires twisting the door slide end retainers outward to remove them and then the dish tray will slide out allowing easy removal of the arm. The top arm is mounted the body of unit. This problem would not have occurred if there was an inline filter on the cold side to filter out calcium (whole house filter). Another way to have corrected this without the purchase of parts would be to run the dishwasher on the rinse cycle 3 or 4 times using 1 cup of lime away on each rinse and also by removing the arms and soaking the arms in a 50/50 solution of water and lime away for 24 hours. This will break down the calicum and enable the arms to be cleaned using a garden hose. New parts however save time and labor in cleaning the arms, however the main drain and supply lines to the arms still need the rinsing prior to replacing the new parts.
First and formost before you buy read everything in trouble shooting your dishwasher. Then you do not buy parts you do not need. First you turn off power, then water. Remove two screws, a rubber hose and a hard line by unscrewing if you are lucky some contractors might sweat this on. No biggie just two extra steps that's all. do in reverse to assemble...
Pliers, Screw drivers, Wrench (Adjustable), Wrench set
93 of 107 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Heating element rusted and cracked
The hardest part for me was pulling the dishwasher out from under the countertop. Once it is out all you have to do is disconnect the power (or power off the fuse going to the dishwasher) then look underneath the dishwasher and you will see where the two ends of the heating element come through. Disconnect the wires connected to the ends by simply sliding off the connector. Then remove the plastic "nuts" that screw onto the ends of the heating element by turning them counterclockwise counterclockwise. Once the nuts are removed you can reach inside the dishwasher and remove the old heating element and replace it with the new one. Then simply replace the plastic nuts and reconnect the wires and you are good to go.
I took the two drain hoses off with the pliers then only two screws that holds the pump. After that the two hot wires which are black and white. But remember to unplug you're washer since the pump is not grounded you don't want to risk being shocked. Hope thi helps. Plus i saved around 250.00 by repairing myself.
Glasses and Cups contained baked on sand after washing.
Removed the bottom tray, it just pulls straight out, once the tray was removed, the bottom revolving sprayer just lifts right off. Under this sprayer is a self-cleaning filter. There is a plastic piece that screws the filter into place, this part unscrewed easily by hand. Once unscrewed, the filter lifted straight up. I then reversed the process with the new filter and the problem was solved. Note: The old filter was full of sand and grime.
seal around bottom of door leaking heavy water onto floor during use
First you must remove all screws around inside door frame, and remove panel. (I would recommend using something to weight door down after removing panel from door as it will try to continue to close) Flip panel over and remove old seal by simply pulling off, paying close attention to how the seal is fitted and direction it faces. Clean area of any debris,and let the learning curve begin, after several frustrating attempts, I found it easier to install new seal by first installing it backwards by sliding seal along its track and groove, this will allow it to loosen up, then remove it and install the seal by lapping it over the the track and snapping/sliding it into place. The repair itself from the service center would of been $180.00 - $200.00, I did it myself for $39.00. I would recommend anybody with a sense of aptitude and patience to do this repair themselves. After some research I found out that this model and problem is a common repair, which is somewhat ridiculous in my opinion, as the machine itself is only 2 1/2 years old and it came pre-installed in a new home.
The original problem was that the dishwasher wouldn't start or respond to any button presses. The Clean light stayed on consistently, but nothing else would happen.
I replaced the main board and control board, which really just involved taking apart the door, unplugging three wires, replacing the boards, then plugging the three wires back in.
After I did that and plugged everything back in, the Clean light flashed, and the dishwasher started beeping. It wouldn't respond to any controls, aside from the fact that pressing the Start button stopped the beeping.
Symptoms: - Just replaced Control Board - Clean light blinks - Start button stopped beeps - No other buttons did anything
Resolution: re-read the instructions that came with the board.
There's a step that says "Transfer model selector plug to the new control board". If you look on your old main board, right by the power connection is a plug that you're supposed to remove from the old board and put on the new board.
I had originally skimmed through the instructions thinking "this looks super easy", so I didn't look at it in detail until I had a problem.
Once upon a kitchen dreary. Washing dishes made me weary. All the dishes would not clean. Gunk clogged up my filter screen. The lower spray arm stuck and rattled. With flying muck my dishes battled. The muck had won and I had lost. The repairman said it would really cost. And so I did a google search. Partselect got me out of a lurch. Correct parts were easy to choose and service so quick I couldn't lose. I took off the old parts and tightened the new No tools were needed my fingers flew. And now my dishes come out clean I feel competent and frugal, you know what I mean?
In order to access the fill valve, dishwasher had to be removed from under countertop. Disconnected water supply line and drain hose under sink. Unplugged unit and removed 2 screws holding unit to countertop. I was then able to pull unit out and replace valve. After reinstallation, the same problem existed. Further research pointed to the control module, approx. $100.00 or the motor, approx. $250.00 - $300.00. I than began looking at new dishwashers, but I did email GE with the problem. They suggested I use citric acid or vinegar in hot water, pour into right rear portion of tub and wait 1/2 hour. After doing that, the dishwasher worked perfectly.
dishes were not coming clean. I found the pump that sprays water was not running
I noticed the circulation pump was not operating. If I turned the motor with a screw driver it would start running. I replaced the pump and now the dishwasher works like new. Very easy to replace the pump but you will have to pull out the dishwasher and turn on its back. I was able to confirm the circulation pump was the problem by observing the motor not running when it should but it would run once I turned the inside motor parts(be careful!). I also had to replace the center sprayer which again was very easy.