GI15NDXXS2 Whirlpool Ice Maker - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Excess ice
Double check the actual part number. While the item looks the same, my unit had a 3 prong plug while the replacement had only 2 and did not fit.
Parts Used:
-
Michael from WATCHUNG, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
a rumbling noise was comming from the back of the fridge
I unplugged the appliance removed the back cover exposing the fan motor.Unplugged the wiring harness from the motor assembly.unbolted the fan motor mounting bracket,and removed. Next I unbolted the fan and motor assembly from the mounting bracket.( I pulled the whole bracket out so it would be easier to reinstall the motor and fan assembly,then reinstalled the bracket with the motor and fan already installed) I installed the bracket assembly with the motor and fan back to its location,plugged the wiring harnessback to the motor. replaced the bask pannel ,and plugged the 110 back in the wall socket
Parts Used:
-
Craig from Birchwood, TN
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Socket set
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replaced motor and fan
I have a grandson that works for Pantex. He replaced the fan and motor in less than ten minutes using only the nutdriver tool. My cost compared to local supplier and labor was about 75% less.
Parts Used:
-
Rex from Amarillo, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
3 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Condenser motor was making noise.
Removed the cardboard baking on back. Unplugged the fan. Used 1/4 socket and removed the 3 nuts. Removed the fan. It is tight quarters. Take your time and the job will go fast.
Parts Used:
-
Joe from Spring Hill, TN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Socket set
4 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
only a partial refill of water bucket (would then run dry and make pump noise)
my sensor was stuck because of age, so I had to remove the water bucket to pry it out. It is easy to see what you have to remove to get to it. I used the mirror and rachet, extensions, 1/4 socket to remove screws. Tips - Remove the plastic door-inner to help working inside the bin. Also plug the drain because you will drop screws. Magnet sockets don't work on stainless steel. Later I found it is much easier to work inside the bin by pulling the entire unit out (shut off water and power, remove lower panel and disconnect drain tube). It sounds hard, but actually is easy. REMOVE THE TOP (4 screws). it stays connected because of wiring, but it allows full access and makes all kinds of repairs easy, especially pump replacement and even the circuit board behind the front panel buttons if you ever get to that point.
BTW Partselect is awesome, I have used a number of times for ice maker and dishwasher. My next project is the washing machine! Always the right part shipped very quickly.
BTW Partselect is awesome, I have used a number of times for ice maker and dishwasher. My next project is the washing machine! Always the right part shipped very quickly.
Parts Used:
-
Thomas from HEBER SPRINGS, AR
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers, Socket set
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
went good
-
Jeffrey from IMPERIAL, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice maker Thermostat not shutting off the making of ice
un screwed the hex screw holding the thermostat and installed the new thermostat and pluged the new part int its place. I undid the front shield so i could get to the plug.
Parts Used:
-
M Edward from Timonium, MD
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old pump gave up
Followed instructions in Sears parts website. Not difficult but tricky to get screws out and back in.
Parts Used:
-
Jimena from FARMINGTON, CT
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Cutter on Ice Maker failed and needed to be replaced
I completely broke down the unit cleaning or replacing any part with rust. The replacement grid assembly (cutter) came from partselect within days of ordering. I was able reassemble the unit with the new grid assemble. Now have fresh ice. Thanks Partselect... you made this do-it-your-selfer very HAPPY! My wife cannot beleive I got the unit back together.
Parts Used:
-
Thomas from Powell, OH
-
Difficulty Level:Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver
4 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Motor sounded like a small little airplane under my fridge, very loud.
Unplugged the fridge first then took the bottom panel off with a 1/4 inch nut driver. Disconnected the wiring & used my ratchet to reach the 3 screws that held the motor. Took me longer to clean the bottom of the fridge then the installation.
Parts Used:
-
guadalupe from RIALTO, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacing Condenser Fan
I was anticipating that the fan would be facing the back of the refrigerator. It actually was perpendicular to the back. There was some difficulty removing the bolts of the fan. I persevered and was victorious.
Parts Used:
-
William from RALEIGH, NC
-
Difficulty Level:Very Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers, Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken ice cutter grid
Unplugged the unit. Removed 2 screws to remove front cover to access the cutter grid.removed 2 screws to the cutter grid, unsnapped power connector and removed broken grid. Slid new grid in place, reconnected power connector, replaced screws, plugged in ice maker and slid back in place. Very easy!!!
Parts Used:
-
John from NORMAN, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
loud griding noise
stopped the fan and noise stopped ordered fan motor and fan with interface cable. Using 1/4 inch nut driver to remove screws from motor bracket installed new motor and runs like new.
Parts Used:
-
David from BLACKLICK, OH
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace the ice cutter grid.
The real difficulty is removing the screws. Even with a nut driver the space available makes them difficult to remove. I went to the hardware store and replaced the screws with screwdriver slots for re-installation.
Parts Used:
-
Thomas from PHOENIX, AZ
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set, Wrench (Adjustable)
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noisy condenser fan
I suggest following video supplied with order confirmation perfect fit
Parts Used:
-
Tom from BULLHEAD CITY, AZ
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!