Models > GH9185XLQ1 > Instructions

GH9185XLQ1 Whirlpool Microwave - Instructions

All Instructions for the GH9185XLQ1
61 - 75 of 96
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Put the Fuse in, then plugged it in came on for a min then everything went out!!!!!
Took the front off and behind a plate was the fuse, so I replaced it for what good that did!!!
Parts Used:
R CERAMIC FUSE,20A/250V,MHC
  • Stephen from SPRINGFIELD, WV
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers
4 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Low power - Slow to heat
Replace Magnetron and then I the inverter unit after I discovered the unit still did not heat properly. Inverter had capacitor that was cracked and I found a diode that was flashing over the printed circuit board.
Parts Used:
Magnetron
  • Thomas from Winona Lake, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
13 of 45 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The microwave door would not stay latched, so it wouldn't come on.
The repair was easy, I just took off a few screws and found the broken latch spring. The real story is how easy it was to find the replacement spring from Partselect! I couldn't believe they had it, and even better yet, I ordered it one afternoon, and it came the next day with normal shipping! Unbelievable! Then I just popped it in and replaced the covers I had removed and it was working again!
Parts Used:
Spring
  • George from Maceo, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
2 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light bulbs nedd to repace it.
Took the the want burned out , and put the new ones.
Parts Used:
Surface Light Bulb
  • Jorge from Bay Point, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
45 of 196 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The glass tray in the microwave got chipped while i was washing it and started to crack.
I just opened the box and set it in. Took all of two minutes.
Parts Used:
Glass Cooking Tray
  • Amber from Loretto, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Replacement
Easy, perfect
Parts Used:
Glass Cooking Tray
  • George from Statham, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Door would not shut
Had to replace 1 latch in order for the microwave door to close.
Parts Used:
LATCH-DOOR
  • joshua from las vegas, NV
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set, Wrench set
Was this instruction helpful to you?
Thank you for voting!
left something in microwave too long and burned parts
replaced burnt parts
Parts Used:
Drive Coupling RING-TURN Glass Cooking Tray
  • Norman from Angier, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
burnt out light bulb
The problem I have with changing the bulb is my microwave is an overhead one and therefore I cannot tip it on its side to easily replace the bulb. I have to drop the lid down and carefully install the new bulb from underneath.
Parts Used:
Light Bulb - 40W
  • Shirley from Londonderry, NH
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Light burned
Unscrewed the lens cover anbd inserted the new bulb. Put the cover back on and there was light!
Parts Used:
Surface Light Bulb
  • Jennifer from Red Oak, IA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Burn't out bulb.
Removed the glass cover and replaced the bulb. Very simple.
Parts Used:
Light Bulb - 40W
  • Carter from McCordsville, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
burned out overhead light
Some difficulty getting screw loosened, once that was done replaced burned out bulb.
Parts Used:
Surface Light Bulb
  • Sharon from Anoka, MN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
rotating glass dish assembly making stange noise
The lady in the Nova Scotia call center should get all the credit for being able to identify the part I needed from only the very limited information I was able to give her. Employee of the month for her. She also had such a great can do attitude. Lawence Baier
Parts Used:
Drive Coupling
  • Lawrence from Excelsior, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Broke a 15 year old glass cooking tray
Ordered the item on a Monday at 12pm and it arrived the next day. Amazing!
Parts Used:
Glass Cooking Tray
  • Stephanie from La Jolla, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
glass cooking tray droped and broken
just replace need cooking tray
Parts Used:
Glass Cooking Tray
  • janice from dunn, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GH9185XLQ1
61 - 75 of 96
Back to Top