Models > GH7208XRB3 > Instructions

GH7208XRB3 Whirlpool Microwave - Instructions

All Instructions for the GH7208XRB3
16 - 30 of 40
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Loud noise
Changed out turntable motor
Parts Used:
MOTOR-TURN
  • Cynthia from DRIPPING SPGS, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
lost the driver
just insert it in the right side
Parts Used:
Turntable Driver
  • Luiz from Washington, DC
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave had no electrical
I was sent the wrong fuse by you. I had to procure a fuse in another manner. Very disappointing. The repair was simple. It just took longer because of the failure to send the correct fuse.
Parts Used:
R CERAMIC FUSE,20A/250V,MHC
  • Larry from HARKER HTS, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lost spring that holds filter in hood that was lost when cleaning it.
simply removed the filter casing from the microwave, then removed both filters and inserted the spring after bending it slightly.
Parts Used:
SPRING
  • Raymond from Mechanicsville, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
it was working fine and it stopped order a fuse and it wasn't the problem
took it to Buttermore appliance in Auburn Indiana and he changed the fan and added another fuse
Parts Used:
R CERAMIC FUSE,20A/250V,MHC
  • Herb from Auburn, IN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Put the Fuse in, then plugged it in came on for a min then everything went out!!!!!
Took the front off and behind a plate was the fuse, so I replaced it for what good that did!!!
Parts Used:
R CERAMIC FUSE,20A/250V,MHC
  • Stephen from SPRINGFIELD, WV
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers
4 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light bulbs nedd to repace it.
Took the the want burned out , and put the new ones.
Parts Used:
Surface Light Bulb
  • Jorge from Bay Point, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
45 of 196 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light Burned Out
Followed the instruction booklet that came with the microwave. Very easy.
Parts Used:
Surface Light Bulb
  • Patti from Coarsegold, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dirty filters
Removed the dirty ones and put in the new ones. This was really not a repair. No tools needed.
Parts Used:
Charcoal Filter
  • Anna from Antioch, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
need new filter
replaced old filter
Parts Used:
Charcoal Filter
  • donald from payson, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Bulb Finally went out
Used an apex bit unscrewed the fittingand down came the light cover. Pulled the old bulb out and had to use a flashlight to line the prongs up to install the new one. Whileeverything was down used an oven cleaner to degrease and clean EVERYTHING. You wouldn't beleive how much grease and debris will accumulate in 5 years. And I only fry bacon once in a blue moon. All in all it was simple to order, clean, and repair.
Parts Used:
Charcoal Filter Air Filter Surface Light Bulb
  • Jeff from Hanahan, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Light burned
Unscrewed the lens cover anbd inserted the new bulb. Put the cover back on and there was light!
Parts Used:
Surface Light Bulb
  • Jennifer from Red Oak, IA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
burned out overhead light
Some difficulty getting screw loosened, once that was done replaced burned out bulb.
Parts Used:
Surface Light Bulb
  • Sharon from Anoka, MN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Replace charcoal filter
Took old one out,and clipped new one in.
Parts Used:
Charcoal Filter
  • Louise from Mason, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
handle on door broken
remove screws from the door trim remove two screws from the handle and replace with new found out the handle is directional had to remove and reinstale in right direction reinstae the screws for the door trim
Parts Used:
Door Handle - White
  • Glenn from Edwards, MO
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the GH7208XRB3
16 - 30 of 40
Back to Top