Models > GEW9200LW1 > Instructions

GEW9200LW1 Whirlpool Dryer - Instructions

All installation instructions for GEW9200LW1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the GEW9200LW1
1-15 of 585
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer was working, but no heat.

  • Customer: ANTHONY from CHESHIRE CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 1016 of 1166 people found this instruction helpful
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils.
Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of needle nose pliers, it was held in place by two screws, once they were removed the fuse came out easily, I checked continuity with a volt meter placing the meter on X1 Ohms and could not get a reading.
I replaced with a new one and put it all back together the way I took it apart.
Then I plugged it in and it worked first time, I now have warm dry clothes.

No heat but would run otherwise

  • Customer: Dana from Grassvally CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 497 of 506 people found this instruction helpful
Cleaning the lint out of the whole machine took quite a bit of time--it was everywhere. Underneath the lint trap was a collection that ultimately ruined the thermal fuse where it restricted the air flow considerably.

Ascertaining the problem was the most time consuming part.

The actual repair was quite simple and didn't take but 15-20 minutes.

Door Catch part had fallen out,/ was missing

  • Customer: Terri from Saint Augustine FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 481 of 484 people found this instruction helpful
Received your parts, Popped them both right into place, Even though only one side needed to be replaced, I wanted them to match up. It was amazing how easy this was. My husband was quite impressed I had ordered these rather then look for either a new or used dryer from some other source.

Burned out heater element

  • Customer: Alan from Brooksville FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 212 of 233 people found this instruction helpful
Remove the kick plate from the bottom of the dryer by sliding a putty knife along the top edge to release the plastic clamps, one on each side about 4" in from the edges. The kick plate folds out and down. You will see the heat shield on the right, held in by one hex head screw. Remove screw and heat shield. The element is positioned in an open-front housing and is fastened to the left side of the housing by two hex head screws, located on the "rail" of the element and right near the two wires. Remove the hex-head screws that hold the element in place and disconnected the two wires by pulling them out by hand or with needle nose pliers. The only difficulty here is the cramped working area...I recommend a stubby socket driver for these two screws. Most of this I had to do by feel because I could not see the screw heads. Once the screws are out and the wires have been disconnected, slide the old element straight out toward you. You may need to disconnect a small plastic hose located to the left front of the element, but this hose just pulls right off. Vacume the dust & lint build-up out of the whole area, wipe out the element housing and clean up the whole underside of the dryer prior to installing the new element. Installation is reverse of removal. It also might be a good opportunity to clean out your exhaust duct and the vent to the outside. (Never use the aluminum foil-accordian-type duct.) If the exterior dryer vent has any kind of screen over it, remove it and get rid of it. Screens collect lint, lint builds up and burns out elements.

Door wouldn't latch.

  • Customer: Melody from North Las Vegas NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 147 of 218 people found this instruction helpful
I can't believe I waited so long to find this part and do this. I got the package very fast, opened it, took the piece to my dryer and popped it into place with my fingers. It worked perfectly! this took all of two minutes and saved me from having to hold the dryer door closed with a stick. Thank you, thank you!!!

Dryer overheated, blew out thermal fuse

  • Customer: Steven from East Norriton PA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Socket set
  • 119 of 137 people found this instruction helpful
I started to repair this and got busy and ended up calling a repair service -- that was the first time. They repaired it for over $200 and said the cause was bad venting. I fixed the vent before using the fixed dryer but it blew again. So I ordered these parts and replaced them myself for a lot of savings. However, the dryer still overheated. Through lots of testing I found the root cause the repairman missed: The heating element had gotten so hot that the assembly holding it warped, hitting the element and shorting it. So a new element is on order. I still needed the parts I ordered here but the overall repair ended up more complicated and expensive. I was disappointed a paid repair person left without further diagnosis. If he had unplugged the vent and checked the heat on the exhaust vent (as I ended up doing) it would have been obvious more than a new thermal fuse/thermistor was necessary. Instead I wasted over $200 on his visit. So my advice is if you're at all handy, repair this yourself. The dryer has a service manual inside the front toe board that walks you through most diagnostics and tests. However, it took a little more than that for me to discover the heating element problem. This was a very dangerous situation that could have easily led to a fire, yet not found by a trained technician!

felt strip came off lint screen

  • Customer: JEFFREY from FALL RIVER MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 87 of 109 people found this instruction helpful
ordered new lint screen, removed old screen, inserted new screen.

dryer door would not stay shut

  • Customer: Pam from Woodbridge VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 72 of 72 people found this instruction helpful
This repair was a cinch. Pliers to pull out the metal piece and a screwdriver to pry out the 'catch' part in the door. Both replacement pieces went right in. I cannot believe how easy and CHEAP this fix was, and I'm so glad I found this site!! I figured I would have to call a repairman and pay big bucks, so I put it off, but the door was getting worse--slamming it so hard to keep it shut. Again, thanks for this great site.

door kept coming open dryer shuts off

  • Customer: RONALD from SALMON ID
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 80 of 143 people found this instruction helpful
use screwdriver topry plastic out plyers to pull out metal latch put new parts in

Door won't latch

  • Customer: Jill from bellevue WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 75 of 133 people found this instruction helpful
I did NOT have to repair the latch on the actual door, just the small metal piece that it hooks on (on the dryer itself) and it took about 10 seconds to.....do it myself. Just used needle nose pliers so squeeze the piece together and fit it in. thanks

Belt Wheel was broken at axle. Terrible noise.

  • Customer: eric from Boulder CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set, Wrench(Adjustable)
  • 33 of 38 people found this instruction helpful
Removed the top and back of dryer with screw socket. It was quite easy. Then, I removed the broken wheel by releasing the tension spring. I replaced the wheel. The toughest part was re-threading the belt. But, even that was simple. The dryer runs smoothly and quietly again!

Dryer motor would not turn on

  • Customer: John from Bluffton SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Wrench set
  • 31 of 33 people found this instruction helpful
After looking at the schematic to see what was in line with the motor, I found the fuse as the first item. I pulled the fuse out and used a multimeter to ohm out the fuse. Upon using the meter I found that the fuse was bad. I typed into Google my part number that was on the fuse and the PartSelect Website came up as one of the choices to pick from. When the part arrived approx. two days later I installed the fuse by first unplugging the dryer and then removing the bottom panel and removing the fuse from the exhaust by using a small 1/4 inch wrench and pulling out the old fuse. I installed the wires on the new fuse and re-installed and put the 1/4 inch screw back in. I started the dryer after plugging it back in and it worked like it should have. Thank you for the part and I have recommended your website to other people already.

Our dryer started squealing and would then stop running.

  • Customer: Kelly from Aptos CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 29 of 36 people found this instruction helpful
After determining that the dryer motor was the issue I wrote down the part number and logged on to partselect.com.

I input the number into the search box and there was the exact motor I needed.

The price was fair and the delivery quick so I figured I would give yuo guys a shot and see how it goes.

The part showed up on time and as expected. It was well packed and most importantly - it was the CORRECT part.

I disassembled the dryer which involved removing the lint trap, pulling out the blower fan and removing the motor cover. The motor was held in with 2 metal screws and wiring harness.

I took the belt off of the tensioner and pulled out the old motor. The motor was mounted with 2 clips which snapped off with ease. Reassembly was a breeze since the motor fit perfectly- the entire transplant operation took all of about 35 minutes.

I crossed my fingers, turned on the gas, plugged it in and........SUCCESS!

Since the dryer was down for over a week the backlog of laundry was piled pretty high. This replacement motor would immediately be put to the test.

It has been 5 days of non-stop drying and no squeeks, no squeels and nothing but dry clothes!

Thanks to Part Select for getting everything right the first time. It made a potentially very bad experience turn out as good as I could have ever hoped.

the dryer only blew cold air

  • Customer: charles from waukesha WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 26 of 29 people found this instruction helpful
actually i found your site before i even looked at the dryer,thats how i knew to check for the thermal fuse.
I ordered the part and it was on my door in 36
hours,pulled the two wires off the old fuse and installed the new,put the back cover on and it has been working ever since,thanks ( your in my bookmarks)

Felt gasket on lint filter loose...

  • Customer: Catherine from Atascadero CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 26 of 29 people found this instruction helpful
Found this site by googling, and it works! I searched lint filters and just ordered based on how it looked...LOL! Husband wasn't home, it looked pretty much like the one I had in my hand, so.... I ordered it. It is the perfect fit and seems to have a tighter gasket glued in all around the screen. Let's hope this one lasts longer than 6 months! Thank you Parts Select for being so fast!! Filter got here in less than 48 hrs.!
All Instructions for the GEW9200LW1
1-15 of 585