GD5RHAXNB00 Whirlpool Refrigerator - Instructions

Our ice maker would work a few days then it would freeze up because it ran to much water in. I finally called Parts Select. The gentleman found the correct parts right away and I had them in two days. Took about 30 minutes to change out with a new unit. Only cost about 120 dollars. If I had known it would of been that easy and that cost effective I never would have took the time to un thaw it so many times with the blow dryer. Buy the new one, quick repair and gets rid of the head ache. Besides you will have ice when you need it. Good luck

Before I began I unplugged the electrical at the wall outlet. 1. Unscrewed the 4 mounting screws. 2. disconnected electrical at the motor. 3. removed the assembly. 4. mounted the new motor on the assembly as described in the instructions. Installed the assembly and reconnected the electrical. Works great, easy job!

Took ice maker out all together we removed 4 to 5 screws had to remove axel to get the broken piece out and new one in my husband said it was easy in and out in about 15 minutes saved about 150. 00 Thanks partslect

I took out the old drawer and inserted the new drawer in the same place! I wish all of life were that easy!

After plugging in the new relay to no avail. I replaced the thermostat. That fixed the problem.

Replaced the Ice Maker Control asssembly. Online video instruction were ectremely helpful. Time to repair was about 10-15 minutes and we have a funcioning ice maker again!

A bit of a tight squeeze for my hands, but very basic as I followed the instructions and watched the installation video. I only had the fridge unplugged for about 20 min..The fridge is as quiet, as it was brand new. The only tool I needed was the 1/4 inch socket wrench. A portable lantern was very helpful as well. Runs very quiet now, like new! Thx!!!

The video on your web site is great!! I had removed old ice maker and found that the main drive gear was broken off. Rec'd new one in 2 days remove bottom cover to put on new ice maker reinstall. Thanks for the help and great service!!! Tom

Fast after a little help from a friend

as per your video

Read the suggestions of possible repairs on PartSelect web site. Ordered part based on these suggestions. Part was received within two days. Followed installation instructions found on the web site. Part was installed within fifteen minutes. Ice bin was full the following morning.

Opened the freezer door. Removed the ice bin from the freezer compartment. Removed with a nutdriver the two screws holding down the shaft holder (the triangular white plastic piece). Removed the shaft holder and the circular seal underneath. Pulled the hexagonal metal shaft up and out of the dispenser motor. Installed new circular seal and reinstalled the plastic shaft holder, etc..

I first viewed the instructional video provided by Partselect to pin point the faulty part. It was the control bracket. I would not have known how to expose the control bracket if it weren't for the video. Also Partselect said 48% of past water dispenser problems were the control bracket; this also helped me pinpoint the faulty part. I ordered the part; it arrived in 3 days. Using the video as a guide I repaired the dispenser in about 20 minutes start to finish. I will always go to Partselect for all appliance problems.

Open fridge....empty old drawer....through out old stuff....remove broken drawer and take downstairs to trash bin. Remove new drawer from package....open fridge. Insert new drawer. Restock with remaining items. Have a cold drink and congratulate yourself for a job well done!!!

Unplug appliance, turn off water supply valve to fridge. Remove rear cover and locate water inlet valve on lower right corner. Remove 2 screws holding valve in place. Pay attention to water line locations. Unplug 2 connections on valve. They are different size so you can't put them back on wrong. Remove all lines from bad valve. Cut all ends off lines and insert into new valve. Make sure they go where they belong. Press firmly into place. Reconnect electrical plugs and screw valve back in place. Turn water supply valve back on and check for leaks. If all is good put rear cover back on , plug appliance back in and your work is done. Easy replacement job.