Enter the code TAKE10OFF at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on May 28 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
inner oven door glass was cracked
Removed the door and laid it flat with the cracked glass facing up. applied duct tape to the broken glass to help hold it together. Removed the screws from the frame holding the glass. lifted the frame off,removed the broken glass and replaced it with the new piece. replaced the frame. and put the door back on the oven.
Turned off breaker to oven. Removed 2 screws, used pliers to remove 2 wires from old element, replaced with new part, connected wires to new element and screwed in 2 screws. Turned on breaker, then oven and new element heated. Very easy!
Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.
every time I would try to do the self clean mode on my drop in range the thermostat blows. Last time it was still under warranty. I took the part number from the repair man's invoice to order the new part.
My husband took the back off and replaced it. The repairman suggested pulling the range out into the floor to run the self clean mode. I have owned several such ranges and have never had to do that and won't now. Easy Clean Oven Cleaner will be the next thing I use.
1- TURN OFF POWER TO OVEN 2- REMOVE OVEN 3- REMOVE BACK PANEL SHROUDING 4- DISCONNECT POWER TO BLOWER 5- REMOVE BLOWER UNIT 5- REPLACE WITH NEW UNIT 6- RECONNECTED POWER 7- PUT OVEN BACK
Cut the power. Undid the screws to the element. Popped off the old element replaced with new,put screws back in turned power back on and Shazam it was up and going
Just screwed the new one on. A repair man said it would be really difficult and a lot of people break the glass when putting it in. But that wasn't true. It was really easy.
I was trying to remove the oven door so I could clean the glass. Spills had run down between the layers of glass.
This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.
Remove the left/right outside trim on the double oven. To do this you will need a phillip screw driver. There is only one screw holding each side located at the bottom of the trim (on the inside between the trim and the door). Remove the trim by pulling out and down. Remove the bottom trim by removing the screws located on the outside of the trim. Remove the trim by pulling down and out. Replace the new trim by reversing the process making sure to replace bottom trim first because the outside trim goes over bottom trim to cover up the screws on the bottom trim
I was able to remove the old element and planned it with what little time off that I could. This would have been maybe 20-30 minute repair at the most. HOWEVER! I was extremely irritated screws were not included? When I called to ask if they were missing they said they didn’t come with the element. Cost me a very annoying trip to the hardware store. Not sure if I missed it on the site that they don’t provide screws - would have been nice to know that before I started. Still scratching my head as to why screws wouldn’t be included? My old ones were as beat up as the element I replaced. I was so irritated I was looking for a spot to leave feedback. Product is fine. Shipping was fine. Sending these products out as they do? Zero stars on that.
Verify power is off to the oven, turned main power supply off for the oven at the breaker panel, located the securing screws for the defective element, used a Phillips screw driver to remove the screws, pulled the element slightly out unit wires are exposed, verify 0 volts at the element wiring terminals, used pliers to remove the wires to complete the uninstalling process, reinstall the element in the reverse order, restored power at the breaker panel
The oven door would not open properly. The hinges needed replacement.
I followed the instructions per a YouTube video. My older model was slightly different in parts used in the video, but the general idea was the same. Very happy with current repair / parts. The door now opens smooth as glass, and I even got a chance to clean some internal parts inside the door.