GBD277PDQ0 Whirlpool Wall Oven - Instructions

I pinpointed the location of the sound, took off the protective plate, felt it vibrating against the plate. I disconnected the power supply, and looked at the wirings and how it was connected, saw some burning residue surrounding the area of the Transformer. Then figured that I could simply replace this. I wrote down the Model and Serial number of the Stove, searched online, found this site. Located the part on the diagram, then simply ordered it. My part arrived in 3 days, and had the part replaced the next day. Couldn't be a smoother fix. Thanks.

After turning of the breaker for the oven, I pulled out the oven, removed the back panel. The High-Temp thermal cutoff was attached to 2 wires, which I unplugged, and then removed the cutoff by removing two screws. I then replaced the part in reverse order, pushed the oven back into the cabinet, and turned the breaker back on.

Verify power is off to the oven, turned main power supply off for the oven at the breaker panel, located the securing screws for the defective element, used a Phillips screw driver to remove the screws, pulled the element slightly out unit wires are exposed, verify 0 volts at the element wiring terminals, used pliers to remove the wires to complete the uninstalling process, reinstall the element in the reverse order, restored power at the breaker panel

I was able to remove the old element and planned it with what little time off that I could. This would have been maybe 20-30 minute repair at the most. HOWEVER! I was extremely irritated screws were not included? When I called to ask if they were missing they said they didn’t come with the element. Cost me a very annoying trip to the hardware store. Not sure if I missed it on the site that they don’t provide screws - would have been nice to know that before I started. Still scratching my head as to why screws wouldn’t be included? My old ones were as beat up as the element I replaced. I was so irritated I was looking for a spot to leave feedback. Product is fine. Shipping was fine. Sending these products out as they do? Zero stars on that.

This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

Easily, Removed the oven with help of my grandson, this model is quite heavy. Open the back cover panel, removed the old blower. replaced with the new blower, covered with the back protective panel. About one hour because some screws much harder to reach.

1) Removed the trim pieces (2 screws). 2) removed the 2 screws holding the oven in the wall. 3) Slid the oven out of the wall cabinet 4) removed the back panel of the oven ( 10 screws. 5.) removed the old thermostat (2 nuts) 6.). Installed the new thermostat and reversed steps 4-1

Very easy. Take the two top screws out and the two bottom holders off. The bottom holders hold the glass up in place. Grab the handle and pull glass out. To install put handles screws back on the glass and slide in place. Once in place install the bottom holders pieces back on. *** I would buy screws because after years of use the head rust out and sometimes they are hard to get off... all in all very easy to install

I looked up the problem and determined I needed to replace the limit switch which is inside the back panel. As a 78 year old woman who isn't afraid to tackle these problems I found this easier than most. Just be sure to disconnect the electrical connection if you don't have long enough length to pull oven from the wall cabinet. I won't put any sheet pans in the oven next time I self clean it.

We followed the instructions given by Parts Service. The only problem we had (Whirlpool left two screws out of spacer bracket and it fell out requiring further removable of inner glass to replace spacer. Process took about twenty minutes.

Unplugged old element unit and plugged in new element. Took two needle nose pliers and a flexible body. Took about 5 minutes. Works fine. Anybody can do it. Make sure power is off at the box.

we live in Venzuela the ordered windows come to us via a forwarder in the US, one glass (the outer glass) still has to arrive. Very pleased with the service of PartSelect, one glass was in stock, the inner glass had to be ordered with the manufacturer. This glass is on its way and will arrive here in Venezuela by the end of May. As I have to travel to Europe next week, I will install both glasses upon my return somewhere in August next. I will sure inform you about the repair which will be done by myself.
regards,
Titus

Thanks to video provided by PartSelect the repair was fast and easy. My second experience with an appliance repair with parts and video from PartSelect. I am a happy customer.

I watched the video on the product page and followed it step by step. Not difficult at all.

I turn off the power in the breaker box and then unscrew the part and replace it with the new one