All Installation Instructions for Maytag Range GA3631XUWG

Burner coil was falling apart.

Used new plug in coil burner.

Parts Used:

Drip Bowl - 6 Inch

Chrome Drip Bowl - 8 inch

Mary Kay from North Charleston, SC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

leg was bent, also metal receiving bracket bent

Removed stove from slot in wall. Bent rear left leg would not unscrew due to bent metal bracket. Used hacksaw to cut out leg, then straightened metal bracket with small hammer and was able to screw new leg in and adjust height by using level on stove before reinserting stove its slot. Recheck level after pushing back in place and adjust front legs if necessary. If not for bent metal receiving bracket, would have taken much less time. Still easy tho. R'cvd part in two days. Very quick.

Parts Used:

LEVELER-FOOT,SCREW,F/S,NYLON

Virginia from Oceanside, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Wrench (Adjustable)

Was this instruction helpful to you?

Thank you for voting!

Oven was not working, couldn't bake

Amazingly simple. Removed 2 screws, pulled off 2 wire terminals, removed broken element. Re-attached wire terminals, installed screws.......baked some cookies to reward myself. lol Actually, my girlfriend replaced this part. I just talked her through it. Thanks Partselect. I wasn't able to save you any cookies though.

Parts Used:

Oven Bake Element

Bryan from Midland, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Broken leveling leg.

This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.

Parts Used:

LEVELER-FOOT,SCREW,F/S,NYLON

Don from Crestwood, MO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

Was this instruction helpful to you?

Thank you for voting!

Stove would not heat up.Guessed it was element

Pulled stove well away from wall - took plug out of socket..Phillips screwdriver. Slotted element into wire thing-y - one connector fell down the back, so had to take back off the stove. Used tweezers to pull wire back into back of oven. Screwed plate over wire.Was thrilled when I turned stove on and element shone brightly. Husband away so had to do it myself. Had a glass of wine.

Parts Used:

Oven Bake Element

Jean from CliftoN Park, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

replace the heater coil in bottom of oven

It was so easy. The video that was sent to me with my order confirmation made it kids play. Took away any of the fear of doing something wrong. Highly recomend using parts select. Fast servic too!

Parts Used:

Oven Bake Element

Al from Concord, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

burner not operating or intermittently

Shut off power at breaker box. Removed top burner unit. Removed old receptacle (Mounting screw was rusty so I drilld out the old one.) Cut wires from old unit. Stripped wires back on old unit. Attached old and new wire with ceramic wire nut. Attached new unit. Reinserted top unit. Reconnected power and "voila". Wife was smiling again.

Parts Used: