FRS6LF7JS3 Frigidaire Refrigerator - Instructions

just installed new shelf

I ordered the part from PartSelect and the order was procesed promptly. I installed the shelf and everyting is back to normal. Thanks!

Pulled fridge away from wall and unplugged. Turned off main water supply feed and removed fitting from water inlet valve. Took off back panel by removing 3 screws. Took out 2 screws holding valve to fridge. Pulled off color coded wire clips. Unscrewed each water tube connector. New valve had quick connectors so had to snip off flared ends of tubing with utility knife. Pushed tubing firmly into new valve fittings and pulled to ensure connection. Reattached wiring and reattached valve to fridge with the 2 screws. Reconnected water feed line and turned on main water feed. Checked for leaks before replacing back panel. Done. No more dripping from water dispenser.

It went okay. My husband did the job and he is handy. We both watched the little "How to" video and that was very helpful.

First I watched the PartSelect installation video. Then unplugged the power and shut off the water valve on the wall. I used a 1/4" nut driver and removed (4) screws on the back bottom cover of the refrigerator and removed the cover. I removed the (2) mounting screws on the back lower right side of the refrigerator and removed the triple water valve assembly. I then marked the (4) water lines and (3) solenoid connectors with numbers, to make sure they get connected back in the same place, and then I removed them. I used a retractable blade knife to cut the ends of the water lines perpendicular. I pushed the (4) water lines into the valve holes and plugged the solenoid connectors back onto the new triple valve assembly. I mounted the new triple valve, put the back cover on, turned on the water, checked for water leaks. There were no leaks.Then I plugged in the power and waited for it to fill up the ice tray. It works perfectly now ! And it was really easy ! Thank You PartSelect for making this repair easy for me.

Easily removed door and installed new parts. Perfect fit.

New bins slide and snap into position with no tools required. EASY!

Opened freezer pulled out ice tray put in new one closed freezer door all done

1. Punched the little circle bolt at the top of the drawer support all the way through the refrigerator wall using a hammer and awl. Removed the remainder of the old drawer support. 2. Previous two small alignment prongs were stuck into the alignment holes, so I had to snap off the alignment prongs on the new drawer supports with pliers to make the supports fit flush with the fridge wall. 3. Stuck new drawer supports into holes in the fridge wall and hammered in circle bolts with hammer.

Simply placed new bin in place. Took less than 60 seconds.

May need someone to hold a flashlight on area during repair. The bottom ridged-tray does pull out easily, exposing three Phillip-head screws. Remove them. Lift the face plate up slightly and pull out to expose the wiring harness behind it near the top. Push the small clip that holds the white plug together and pull to separate. Set faceplate aside. Find and remove three more Phillip-head screws, one in top middle and two on the sides. Pull the unit forward enough to see the two Phillip screws that hold the metal pieces over the rotating arms of the broken lever. Cannot pull this unit out too far as the water hose from refrigerator restricts movement. Use needle nose pliers to reposition/release the spring clip that rests against the lever. No need to remove the entire spring. Remove the two screws. They are short, so be careful not to drop them or the metal pieces they hold down. Use needle nose pliers to retrieve them if dropped. Lift the broken lever up to disengage its rotating arms from grooves. Remove the broken lever by pulling up or pushing down, depending on where it is broken. Take new lever and insert from the bottom and insert both arms in grooves. Re-insert the two screws and metal pieces (large piece on the left). Place spring clip on arm of new lever. Screw the unit back with three screws. Re-connect the white plug of the faceplate. Reinsert the faceplate on refrigerator by aligning holes with hook-prongs and push in and down to lock in. Add the three screws at bottom to secure. Reinsert the bottom and push in to lock. Check lever operation.

Taking it apart is sort of common sense, however putting it back together can be made a lot easier using todays technology of . Digital photography. Take pictures at each stage of disassembly and reassembly be comes very easy and you may only have to do it once instead of multiple times.

after I contacted Frigidaire and they told me that it was the vent fan and told me where it was, looked up the part and got a new one from Part Select. When it arrived I unplugged the old one and plugged in the new one and reattached the holding bracket. No tools required. I then turned on the dishwasher and it works perfectly. If you get an "ou" error message on your Frigidaire Dishwasher, the money you will save is great!!!!

take of the tray & take parts out & installed the new ones

Popped the old water filter out and popped the new one in, just as easy as that!!