Models > FRS6LF7JS3 > Instructions

FRS6LF7JS3 Frigidaire Refrigerator - Instructions

All installation instructions for FRS6LF7JS3 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FRS6LF7JS3
601-615 of 638
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water leaking from dispenser

  • Customer: Gary from San Angelo TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Used a nut driver to remove the small panal from the back of the refrigerator. Removed the two screws holding the valve in place. Unscrewed the water lines from the old valve and cut the ends off of them. Push the water lines back into the new valve. Unpluged the wiring from the old valve and installed them in the new valve. reinstalled the new valve and put the cover back on. Tested system for proper operation.

No power to front panel for ice, water, and light.

  • Customer: Derrick from San Antonio TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the ribbon from circuit board in door to the circuit board which controls the water and ice dispenser and back light. Unplug the refrigerator before any repair is attempted. You can short the boards when replacing the cable. Remove the front plate where the buttons are. Be careful, it slides up then out. once you remove the outer panel, you will see the ribbon which attaches to the front panel to the circuit board in the door (of course freezer side). on the plate you just removed, there is a white cover plate secured with four small philip head screws. Don't try to replace the ribbon without removing this cover. If you do, you run the risk of breaking the the ribbon and then you'll have to order another one. Make sure you note which way the cable is inserted. Insert the cable in both slots on the door and panel. Replace the screws and front panel.

Fit great

  • Customer: Elizabeth from Havertown PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Slid bin into door

ice dispenser and ribbon cable broke

  • Customer: Angel from Miami FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
i dissasamble the water & ice dispenser and substitued the ribbon cable for the new one.

broken frig door bins

  • Customer: john from Miami Gardens FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pushed the bins in place,very easy.

No water to the icemaker

  • Customer: Patrick from Rosharon TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed and replaced the water valve-it was a very easy repair.

Stop crushing ice.

  • Customer: Lee from Hockley TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Crusher housing had broken so I ordered the part and replaced it. I have since put it back together twice. When I first installed it it crushed the ice no problem. From that point on it seems to lock up and won't crush the ice, cube ice works but the blades seems to hang up after the first use. I can turn the cog by hand but I have to turn it backwards a few times before it turns freely, however it still won't crush the ice. I took it apart and put it back together again. Same thing happened after the first time I tried it. Can you help me. The old crusher broke into. Could something else be locking up?Thanks for the help

Washer broke off

  • Customer: Rafael from Port st Lucie FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Had help with one person,to lift the door.But the part was easy to install.

Replacing shattered glass shelf

  • Customer: Deanna from Springfield MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I was extremely happy with the prompt shipping. And it looks just like the other glass shelves in my refridgerator, complete with the tiny little dots on the front of the glass. Installation was easy. Just place in the frame.

light socket burned out

  • Customer: Judith from Gambier OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
snapped the wires from frig onto the proper prong and viola,it works. The proper prong is identified by the size because there are two prongs with the wires and two connecting prongs in the socket. I talked to a very helpful representative and she gave me the number for Frigidaire, when I was confused by the placement of the wire. Wish I had remembered her name to share with you. As it turned out I didn't need to call Frigidaire.

Ice maker not making ice

  • Customer: Dawn from Philadelphia PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
By removing the old water filter and installing the new one

Not getting cold in lower Refrigerator

  • Customer: Charles from Wallingford CT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watch the video provided by PartSelect and did exactly the same percedure. Shows what screws to remove and how to remove and replace the part. The freezer compartment was iced up quite a bit so defrosted it before installing part.

Bottom hinge for refrigerator door was broken/missing

  • Customer: Frederick from Shepherd MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
simply took the screws out of the top of the door(after first emptying the door), picked it up off the bottom support and laid it on the counter. Used a needle nose pliers to remove what was left of the bottom bearing and replaced it with the new bearing. Placed it back on the support and put the top door mount back where it belonged. replaced the plastic hinge cover and it was as good as new. Really very simple.

The Plastic Tabs that hold the shelves are too thin/small

  • Customer: Cheryl from Huntsburg OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The shelve bin tabs broke because they don't snap in properly so they get knocked out occasionally. They hit the floor and if what's in the door is heavy and lands on them they break. Snapping in a new one is not a problem, it's ordering/paying/shipping/waiting. They need re-designed so they fit more securely.

broken crisper drawer

  • Customer: MORGAN from ARCADIA LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
just pull out broken crisper, and push in new crisper drawer.
All Instructions for the FRS6LF7JS3
601-615 of 638