Models > FRS6LF7JM3 > Instructions

FRS6LF7JM3 Frigidaire Refrigerator - Instructions

All installation instructions for FRS6LF7JM3 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FRS6LF7JM3
601-615 of 642
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

no water flowed to the ice maker

  • Customer: Levern from Mc Donald TN
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
1. Turn off water in line to refrigerator. 2. disconnect hose from refrigerator. 3. Remove back cardboard panel at bottom of refrigerator. 4 Remove 2 screws holding in the valve assembly at bottom right. 5. best way I found to remove hoses (all color coded) is to cut with razor knife at the white collar. cut clean and square. 6. disconnect electrical (also color coded) 7. connect hoses to valve assembly by pushing hose firmly into hole. If you are familiar with PEX then this is the same. Reconnect electrical. Reconnect to refrigerator... 3,2,1 your done. It will take a couple cycles to get the air out of the lines.

clear tray broke

  • Customer: Richard from Houston TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
just snapped it in - 1 minute repair

"Popping" noise when opening the refrigerator door.

  • Customer: Alan from Plantation FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I removed the food on the door and placed it in the refrigerator. I placed a plastic sheet over the opening of the refrigerator to keep the cold air in. Then I removed the bracket for the upper hinge, remover the door and placed it onto a table. Then I removed the plastic bearing from the bottom of door. I then replaced it with the new bearing. Then I removed the lower bearing and its bracket from the refrigerator. At this point I had to modify the new lower bracket by removing the alignment tab with a dremel because there wasn’t any hole in the housing for it. Then I attached the new bracket and bearing. Replaced the door and upper hinge and the job was complete. It took only about a half an hour to finish.

plastic bottom door bin cracked and broke

  • Customer: Tom from Brant Lake NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
popped old one out...new one in...easy

Ice Maker Not Getting Water

  • Customer: Edward from Cuba NM
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Followed the instructions from another person in the Part Select water valve section and from the video on the same page. Excellent instructions and very easy installation. Water dispenser and ice maker began performing properly as soon as the refrigerator was plugged back in to the power.

broken door bin

  • Customer: Pat from Cincinnati OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Snap the new one in

Old filter was dirty slid it out

  • Customer: JERRY from LIBERTY CENTER IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Slid the new one in EASY !

Our refrigerator ice maker was broken, crisper draw was broken, and shelf support was broken.

  • Customer: Gary from North Smithfield RI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
We decided to get a new fridge, after the " sticker shock " of new refrigerators we decided to repair the one we have. Two screws and one plug and the ice maker was replaced, took out the broken crisper shelf, put in the new one and that was done, instructions were great. I actually had to watch a " how to " video, ( provided by your web site ) to change the shelf support, very easy. thanks, Gary Hoyle

Shelf broke while I was cleaning it

  • Customer: Elaina from Los Angeles CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just slid the glass back into place

This plastic bottom door bin had cracked and was broken, unusable

  • Customer: Patricia from Greenville SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simple install, fits in a groove.

the brackets on the crisper tray broke

  • Customer: John from Lockport NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
after watching the video I followed to the tee used the screw driver tapped out the old peg and removed the stem in minutes I was tapping in the new parts

Routine replacement of water filter

  • Customer: William from Ooltewah TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Push the button on the right side of the ice maker filter compartment which releases the old filter. Just pull old filter out and slide the new filter all the way in. Be sure and mark on the new filter the date that will be time to change the filter again. I ordered the filter on one day and received the filter in the mail the next day and I had not paid extra for overnight shipping.

Broken Crawer Cover

  • Customer: Orrin from Punta Gorda FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took out the old and put in the new! Piece of cake!

Clinking sound and you can feel it in the handle of the door.

  • Customer: Jim from Verona WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The repair was easy. After looking at the diagram and locating the part need i just ordered it. But I wish I had taken the door off before ordering as I really need a second part. So resulting in extra shipping cost. Parts that were needed were 240328201 and 240457702. Tks Jim

needed a new water filter

  • Customer: Laura from La Porte TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I pushed the button to eject the old cartridge - it came out - I pushed the new one in until it locked in place - I reset the filter light on the front. This took less than 1 minute.
All Instructions for the FRS6LF7JM3
601-615 of 642