Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Wretched screeching noise
Make sure you order a new belt and a new drum glide with the rear drum bearing assembly. If your bearing is worn out, so are the belt and drum glide!
1) Use a flat screw driver or putty knife to release the blind clips that hold the front side of the top of the dryer cabinet down 2) Swing dryer top up and remove two screws that hold the face of the cabinet. 3) Unplug the wiring harness and remove the cabinet face. 4) Remove the 3 screws that hold the drum to the bearing assembly (accessed from inside the drum. This makes it easier to remove the drum as the bearing assembly can be difficult to remove before you see how it snaps together 5) Reach under the drum and take the belt off the motor pulley, then remove the drum 6) Remove the old bearing assembly from the socket (slide up then out) 7) Remove the two screws that hold the bearing socket to the dryer 8) Fasten the new socket to the dryer (you'll need help doing this unless you have REALLY long arms because you have to reach inside the driver and the back of the dryer at the same time) 9) Grease the socket with the supplied high temp grease 10) Bolt the new bearing assembly to the drum and put the new belt around the drum 11) Put the drum back in and snap the bearing socket in and down 12) Guide the new belt around the motor pulley & tensioner 13) Glue the new drum glide / felt piece to the front cabinet 14) Put the cabinet back together
The Dryer Drum Would Not Move. Motor Worked But Drum Didnt.
First I read the manual on how to replaced the dryer drum belt. Second I took off the front panel. This would involving taken all screws from the top of the dryer face and the front panel. Thirdly I removed the exhaust attachment. Then I saw that the belt broke. Really it looked torned apart. I believe too heavy of a load in dryer. I then installed the new belt and reversed everyhing I did to start. The dryer runs great. This is not that bad of a job. If you can do it yourself, why pay hunreds on a service man to do the job.
I removed the front panel to see the belt was snapped in two. The front roller is sping loaded, so I gave it a little tention, slid the belt back on and viola! it was that easy. If your washer starts to vibrate more and sounds louder than normal, get a belt as soon as possible because that may be the problem. Once I put on the new belt, the machine ran as quiet as it did when I first bought it.
I removed the top of the washer by removing two screws on the back. I located and bypassed the lid switch to make sure that wasn't the problem. The problem still existed so I removed the two screws that hold the front panel of the washer. Using a flashlight, I located the drive belt and immediately saw that it was out of position and had pieces missing. I cut and removed the old belt, placed the new belt on the tub pulley and slowly maneuvered it onto the motor drive wheel. I then squeezed the tensioner pulley so that the belt was seated. I turned the timer dial which started the washer and it immediately began pumping the water out of the tub. Problem solved!
Replaced pump, by removing back panel and removing the two screws holding the pump to the bottom of the machine. The only difficult aspect was dealing with the hose clamps, these were extremely awkward to work with in a confined space. The repair would have been less than 30 min if the hose clamps weren't so difficult to put back in place.
timer wouldnt clock it would just keep washing & washing
I removed the screws holding the access cover in place than the screws in the plastic ends than the screws at the bottom edge of the control panel pulled the button on the back of the timer removed the handles than one screw under the handle area to remove the timer it was easy
A bit iintimidating in trying to get the knob off the timer without breaking it. finally discovered the plastic tip that went straight thru to the back, pulleed it out and walla walla the knob came off easily. Getting to the timer was a bit interesting, was not sure how far I had to tear down the washer/dryer combo front. Once I got to the part it was easy to do. I have three of these machines, two in my daughter's houses so now am dconfident i can repair if needed. Got the wrong part at first and had tosend back for the right on, got the timer for the dryer first. Expensive parts.....
Took off front panel, removed drum and replaced parts listed. A bit tricky to keep small parts in place. However, masking tape helped. Best of all was the online diagram of how the parts were assembled. In addition, taking step by step phone pixs aided in replacing parts since there was some down time between diagnosis and installation.
Unplug the unit. The top of the dryer is held down by 2 simple friction pins. By lifting the dryer top above it's front door panel the top will swing up. Prop the top up so you can reach down the front panel. There are 2 Phillips screws about 6 inches down on the dryers front panel. Remove the 2 screws, tip the front panel toward you it will slip off the dryer drum. Remove the 2 push on wires attached to the door switch. Gently lift the front panel off the 2 hinge points at the bottom and set it aside. The parts that your going to replace are the 2 solenoids on the burner assembly. The burner assembly is located on the lower left side of the dryer. Remove the 2 Philips screws that "clamp" the solenoids in place. Pull the 3 & 2 wire friction connectors off the solenoids. Lift the clamp off the top of the solenoids. Pick the 2 solenoids up off the valve assemble. Put the 2 new solenoids on the valve assembly push the wires back on, put the clamp back on and resemble the dryer. *Note: just to make a quick check on the continuity of the solenoids. I suspended the dryer drum so it could rotate without damaging it, put my clamp on amp probe on the 120v line to the solenoids the 3 wire one was good the 2 wire one was open.
I followed the written instructions that came with the kit. They were relatively straight forward. Had problems getting the burner unit out. Had to disconnect from 4" tube and disconnect all wiring. Kit came with parts not needed. Only needed to replace orfice and regulator control. Tight area to work in.
Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
14 of 30 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer wouldn't spin
I used a screwdriver to remove the front of the washing machine, fit the belt around the main pulley, held in the spring loaded tension pulley, and threaded the belt aound. It works great! I really need this inexpensive repair, since my job was downsized, and I can't afford to pay anyone.
Dryer door would not close, part had broke and fallen in. Once part was received it took less than an minute to put the new one in and I was back in business.
thanks for making it easy to find the part needed. and the delivery was fast!
I removed the front access panel above the washer and removed the top dryer front panel. Then pulled out the drum and noticed the drum support ball stud had broken off, rather than order a new one, I welded it back on with a mig welder. I then replaced the drum support bearing and reinstalled the drum. I then installed the new belt before placing the front top panel in place. I removed the small vented panel on the back side to access the belt tensioner and fit the belt around the pulley and motor shaft. The whole job took less than an hour.
Rear plastic drum support bearing got worn making the shaft come in contact with the metal bearing bracket. That contact created a groove overtime and eventually snapped the shaft tip off.
Cut power off. Remove all the screws from the front panel. (where the controls are) working from the bottom to the top. Insert putty knife between the dryer and the control panel and push down to release. Carefully disconnect the wire harness. You will find 2 screws at the bottom and 4 on top holding the dryer door. Remove and expose the drum. Remove the drive belt Remove the drum. You need a 5/16 nut drive to remove the bearing bracket and an extra set of hands to hold the support from the back. Re-install the parts. I used bearing grease to make it run smoother Attach the new shaft to the drum and reinstall the drum (its best done with help)
Re install everything back again. And you are done
