Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Icemaker would not eject ice from tray
After three years of cussing this 5-year old fridge for not ejecting the ice, and having to reach in and pull it out by hand, I fixed it with $100 and five minutes. Worse, I probably could have gotten Sears to honor the warranty and replace it when it first started acting up.
Repair could not have been easier. Loosened the two screws/fasteners with 1/4" drive socket set (straight-slot screwdriver wouldn't bite in the shallow slot). Do not remove screws completely; assy lifts up and off the screws for removal. Turn the unit slightly, unclip the electrical connector and remove. Installation is the reverse. Ensure assy sits flush on the screws to assure tray is level.
Although I probably could/should have unplugged the fridge first, I did not. I made sure the ice maker assy was off prior to installation to keep it from cycling on as I attached the ice maker electrical connector, which is before the remounting procedure.
Now it's making so much ice I have to find the plastic shelf cover for the ice bin to keep it from overflowing (which also helps move the ice level bar up to temporarily suspend ice production).
everything in refrigerator freezing even on warmest setting
To access the part you have to remove the back panel of the freezer compartment from the inside of the freezer itself. There are four screws to this panel. I emptied the contents of the freezer, took of 2 shelves and brackets to gain access and removed the cover. Located the part , cut the wires with a wire cutter and left a small tail ....MAKE SURE TO UNPLUG REFRIG OF COURSE ... the part is clipped on the coils , added the new part. matched the color wires and added the connectors , crimped the wires and added a little electrical tape and put the panel and shelves back. THE REFRIG IS WORKING LIKE A CHARM
Ice maker wouldn't change from crushed to cubed ice
First I pulled the ice tray out so I could see the solenoid housing/ice tray support(1 unit). Below the ice tray there are 2 screws that hold the solenoid housing/ice tray support. After removing those the assembly lifts up so you can see the wiring harness to disconnect. I pulled it out and removed the 2 screws to open it up. There is 2 screws holding the solenoid in place and one ground wire. This was an easy fix and I know I saved a lot of money.
ice maker cycling properly but not getting water on fill cycle
1.Unplugged appliance. Removed rear access panel, turned off water supply valve, removed two screws holding water valve assembly in place. 2. Removed and drained all water lines. 3. Removed three electric solenoid wiring connections. 4.Cut and marked all water lines to facilitate new connecting procedure (instructions provided with the new valve assembly). 5. Inserted the water lines into the new valve by applying a bit of vaseline on tubing end prior to pushing lines into O-ring fittings. 6. Clean the embarassing dust from under the appliance!!!
Note: All lines, wiring, and valves were color-coded to prevent connecting to wrong lines and electric solenoids.
Note: Be sure to remove water inlet supply trough to rear of ice-maker. This tube may freeze solid and prevent water from filling freeze tray. This is done by turning the inlet pipe on the back of the cabinet 1/4 turn and retracting from cabinet.
1) - removed the water tray. 2) - removed the three (3) screws hidden by water tray. 3) - removed entire dispenser faceplate by carefully sliding it up, and then pulling it out CAUTION: there is a ribbon wire connector between the faceplate and the dispenser unit; carefully disconnect. 4) - removed screws retaining the dispenser unit in the door. 5) - disconnect water tube (exit) from the dispenser unit and remove dispenser unit. 6) - carefully disconnect water actuator (paddle) two-wire electrical connector. 7) - remove two small metal "hinge-cover" plates that retain the water actuator (paddle) and remove actuator. 8) - install new water actuator (paddle), reinstall the two small "hinge-cover" plates, connect the two-wire electrical connector, make sure the return-spring is connected to the new water actuator (paddle). 9) - HERE IS THE HARDEST PART - as you reinstall the dispender unit into the door, make sure to reinstall the VERY short water tube back through the dispenser opening - long, skinny fingers would be very helpful. 10) - The remaining reinstallation is pretty straight-forward (the reverse of removal).
The parts came within 2 days. The delivery was great. I took the food off the door, then removed the top hinge. Lifted door off bottom hinge and laid the door on a blanket on the floor. I then had access to the closing mechanism top and bottom that is just two plastic cams that lift the door as it opens. The weight of the door then is used on the cams to help close the door with the appliance level. It was very simple and assembly was just reverse order.
Water coming out of the ice maker when dispensing water from the door.
This issue was noted in the advice area as being a filter, or valve assembly. But it turned out to be a diode kit that was causing this issue. I don't know why I could not find this issue anywhere on line? When I received the diode kit there was instructions that noted exactly the problem I was having. The fix was easy just a few wires cut and spliced and viola fixed.
Removed 4 screws holding face plate onto ice bucket. Removed the 3 screws holding the ice crusher housing. Noted postion and rotation of teh s;ring loaded ice selecting rod. Removed broken crusher housing. Reveresed process for installion. Took for test drive. Operational...
This could not have been easier. I came to this website looking to see how much the part was before i called a repairman to come do it. I saw everyones instructions and decided to try it myself. To replace the ice maker you basically unscrew 2 screws, unplug the broken one and remove it. Plug in the new and tighten the screws to hold it in place. I would have been REALLY unhappy if i had called a repairman and saw that was how it was done. Could not have been easier
The repair was easy. The problem was the lack of explanation. This may help other customers. I was told by the virtual trouble shooting system that about 30% of the cure was to replace the water filter and 70% was to replace the water valve. I did both and still had the problem. People need to be told why they have to replace the water valve. The reason is this. The valve has a very small leak in it that lets water continue to flow into the freezer compartment drop by drop. Eventually, this freezes and clogs the hole , so no water can pass and thus no ice can be made.In either your web site or another they stated that it may freeze up here, but there was no connection to the water valve.It seemed like it was another topic. Its very hard to see the frozen area, unless you remove it from the freezer area. I wish I was TOLD TO DO THIS, after i replaced the valve It would have saved me a repair bill. I hope this helps others. Take care-Bill
Unscrewed the water line cover. Removed the platic case around the water filter base. Everything went well until I tried to remove the two water hoses. After I finally figured out that I had to push in the release washer while pulling the hoses out, things went well. Unfortunately it took several hours of wasted time and several searches on the internet to finally figure this part out. From there on out it went smoothly. Old base came out with two screws. Reversed process for reinstall of new base. Water hoses just slipped back into place and locked themselves in. Just takes a little patience.
