Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Oven not heating to desired temperature
Replaced clock control by removing surface burner control knobs and plastic nuts, and then the cover over the oven control. Two screw hold the clock in place, after removal and disconnecting the plug-in you can reinstall the new clock control. The Heat Sensor inside the oven will also need to be replaced. It is located inside the oven and attached with two screws; the back of the oven will need to be removed to unplug. Reverse removal procedure and turn the power back on to the stove.
Oven light receptacle broken - bulb base broke off
Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.
right side hinge on oven door, not pulling door closed tight enough.
Found that the right hinge spring was sprung loose from its stock position. So I replaced both hinges. Remove the oven door, remove the side trim plate from both sides of the oven door. remove inside of the door to reveal the hinges. replaced both hinges, and replace all covers and put door back on.. I replaced both hinges because if one was wore out the other would not be far behind it.
The burner would not light by itself, and the flame was lopsided.
The repair was nothing, but the diagnosis was a bit tricky. After carefully looking at the burner head, (cast aluminum) I pretty much figured out that the 4 small cast aluminum bumps that keep the burner cap positioned up in the air the correct amount to allow gas to flow under the cap, were worn down, preventing the gas from exiting properly by the igniter. My guess was correct. The new burner head solved all my problems. I love Parts Select for the ease of finding the correct parts and how fast they ship their orders. Great company, great service. Keep up the good work
the gasket around the oven door was severly scorced and hard. Would no longer seal door.
Easier than painting my toenails!! The gasket came out easily just by pulling with my hands. Replacing it with the new one was even simpler. The clips are already attached to the gasket and easily slip into the holes on the door. I used the end of a tupperware orange peeler to push the unfinished ends of the gasket into a slot at the bottom and that was it! A new, perfect seal and it looks and works great!
My inner glass shattered during the cleaning cycle.
I looked online and read what other people had done. The best advice was keeping all the screws in the order they were taken out. I also separated the screws that had come from the top, sides and inner side of the door. This helped immensely as I reassembled the door. I spread out a heavy garbage bag that I cut open. This kept debris and glass off of my kitchen floor. This is NOT a difficult repair; Parts Select said it would take three days to get me the glass; it arrived in TWO! Start to finish, the entire job took just about an hour. I saved myself over $100, and again, this is NOT difficult!
Oven Door Light Switches Wrecked by Heat from Oven
Pull old switches out with pliers and replugged new switches. On main oven, plug casing was melted (wife left broiler on with oven door closed) so had to break apart old casing and individually plug the the wires into new switch and amazingly, it worked! Just gotta keep the door open when broiling.............
I removed the sensor from inside the oven with a 1/4” nut driver, pulled the sensor out slowly and then took the connection apart and found out that the connector was different, I cut the connector off of the oven side and then cut the connector off of the new sensor and wired it together. I am still trying to find the ceramic nuts. My oven is working for now. Very easy fix, just wish there were ceramic wire nuts with the new sensor
Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....
Pulled out stove, took side panel off on switch side of oven, unplugged old switch, pulled the old switch out the front of the oven, put in new switch and plugged it in. Then put oven back together and pushed it back into space. (Make sure to turn oven off at breaker box before you make repair) you could easily get shocked if you don’t.
Simply took oven out of wall, removed back plate, unplugged old sensor, went in the front and unscrewed old sensor, put in new sensor, went in back and plugged in new sensor, put on back plate, push oven in wall. Turn on power