FGF337ECC Frigidaire Range - Instructions

Followed service sheet. Measured 2.6 amps draw at igniter wire which should have been 3.2 amps. Replaced igniter and problem resolved.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I made sure I memorized just how the wires would re-connect with the wirenuts. I then re-assembled everything. Be sure to read all the instructions, especially how to properly install wirenuts. I was able to access the wire connections below the oven chamber through the drawer at the bottom of the range. This is an important detail.

removed the old igniter, installed the new one. 15 minutes, piece o cake!

took drawer out, removed tin covers, found igniter and removed,snipped off parts to put on new igniter ,wirenutted old to new put back together ,we had ignition! all in all pretty easy job! detailed instructions that came with new part were easy to follow and precice

Pull stove out to get behind it,unplug temperature probe plug. Remove temp probe from oven by removing the screw holding it in place on back of oven. Cut plug off temp probe unit leaving as much lead wire as possible on plug end. Strip wires on new probe and end of plug wires(one quarter inch). Then I used two small butt connectors to join the stripped wires,one for each pair of wires. Two small wire 'nuts' may also be used as the connections are outside the oven and not exposed to the heat of the oven while it is in operation. Hope this helps the inexperienced 'do it yourselfers'--:)

Took 6 screws out holding the top on from the sides. Lifted the top front, popped out the spark module, Took 6wires off & reversed the processed to install the new one. I was really amazed when I ordered it Wednesday and it arrived on Friday. Believe me I bookmarked this site.

took off bottom pan in oven and replaced ignitor

Removed racks. removed two screws in back of bottom shelf of oven.Do not know what type of nut or other fastener was on other end of those screws as they would not tighten when I put them back in. However they are in the holes and the shelf isnt going anywhere.The shelf lifted right out lifting the back up first and sliding out from under lip in front. easy access to igniter use a nut driver for this.In the bottom left corner there was a triangle shape cover that needed removed held by one screw. both wires had clip in style connectors that come right out.Cut these off with plenty of wire to attach to new wires with wire nuts provided with new igniter.Put everything back like the old came off. I used a little electrical tape over wire nuts.Closed oven door and tuned on oven and watched my wife begin to smile as the igniter turned red and oven kicked on.

The day after Christmas I searched the net reading various reviews, etc. PartSelect seemed to be the easiest site to navigate and offered How To's notes. Wednesday, less than two days later the oven igniter arrived. This was the third igniter in six years. The grandkids watched me intensly as I read the How to's and easily installed the new igniter. Because of the ease with the website and the fast delivery I am keeping PartSelect.com as part of my resources for the home self doer. The cost was competitive saving me over $100.00 doing it myself. Thank you PartSelect. Joe W Cleveland, Ohio.

Removed broiling drawer to gain access to the igniter. Remove igniter from mounting bracket, ,cut wires, attach new igniter wiring and reinstall the igniter on the bracket. Reinstall the broiling drawer to complete the job.

took off door, oven floor and burner cover. cut the wire for the old igniter and used ceramic nuts (provided) to hook up the new one. screwed the new one on with old screws, tested and re-assembled. Saved a hundred bucks easily, but I have some basic electrical back ground.

First, I took out the racks. Then I removed the bottom cover of the stove. (This was in place by two screws that I used my drill & socket set.) Next, remove burner cover by a socket set. Finally, in the corner was a metal cover that covered part of the electrical connections. I then used the screw driver to undo the screws that attached the igniter to the oven. I undid one wire connection, and wired it with the new one on the igniter. (To make sure I wired it correctly.) Then I undid the other wire, and connected it with the new wire (using the new wiring nuts provided.) Done! Now just put all the parts back together.

disconnected the (2) wires of old igniter from (2) wire nuts located under oven in back of bottom drawer, took out (2) mounting screws holding igniter assembly and held it together to new igniter assembly. Stretched out wires together and cut new wires same length as old wires, then mounted new igniter with same (2) screws and connected wires with new included wire nuts and replaced all other oven parts, turned on oven and had a nice TV dinner! :-) Extremely pleased with PartSelect. Ordered part on Tuesday night and had it by Thursday night the week of Christmas no less! Kudos to PartSelect! Great service!

After reading the input of others on your site I ordered the igniter. Within a short time it was installed and the oven works fine. Thanks for the help, jc

First i disconected the plug went right where the trouble was.removed the two screws and the safe plate that is protecting the wires.disconeted the two wires and replaced the new ignighter. put everythin back together tried it out ond guess what ??? it works .. Thank you