The Spray arm and the support had come off during operation and subsequently melted on the heating element. This was our fault, as a knife had slipped through the lower dish-rack and acted as a ramp to launch the spray arm as it came around. The support was a simple 1/4 turn counter-clockwise until it clicked into place, drop the strainer basket into position around the support, them push the spray arm into place until the catches snap over the retaining ring molded into the support. All told, about 10 minutes, max.
Electrolux part number PS1524955, lower spray arm.
Problem. Dishwasher was spraying water out the bottom of the door. The spray arm was damaged when the heat shield overheated, causing the shield to contact the heating element. This resulted in the spray arm melting, causing water to be sprayed out the small gap between the dishwasher door, and the dishwasher bottom pan.
Repair Lower spray arm is easy to remove. Release the arm clips at the center of the spray arm. When the clips are released, lift and remove damaged arm. Replacement arm is attached by pressing down on the center of the spray arm. The new unit has smaller heat shields so it will be less prone to overheating.
Thanks for the fast shipping. Part was recieved in a few days. For just a few dollars, the handwashing is over.
It would sometimes work, which led me to believe it was a switch. Looked on line and found the mail switch to go on was in the latch. I took it apart, 6 screws, wiggled the switch and it went on. So I found the door switch to be bad. It was very simple to change the switch.
After figuring out the problem wasn't the water inlet switch, I replaced the switch assembly for the water level float. Cut off supply water to dishwasher, removed the 2 screws holding switch assembly, and installed new switch. 15 minutes, very easy job.
Dishwasher was leaking at the lower left side of the door.
Probably the easiest repair job that you could encounter. I removed the old gasket from the door frame. Cut the new gasket to length and pushed it into the door frame.
Broken friction cable on the right hand side. Remove screws that hold dishwasher to cabinet, pull out the dishwasher far enough to get to the friction cable and rear spring. Remove broken cable. Attach new cable to rear spring and connect to door hinge. Push back dishwasher and screw in the two screws that keep the dishwasher attached to the cabinet. Very simple.
The spray arm comes off into 3 parts but is really only supposed to be one. I removed the nut from the old assembly and attempted to place the new assembly on by hand. The new nut seemed to be slightly smaller than the original so it would not attach to the dishwasher. Using a kitchen knife, I removed the new nut from the arm unit and attached the new arm to the original nut and it went back on easily. The connection of the new arm to the new nut was 3 tabs that needed to be depressed with the knife and was a different conection method than the assembly that kept coming off in the wash cycle. The replacement part had a much better design than the original.
Discovered upper wash arm had come off. It looked like it was repairable, but the bushing/clip holding the arm came off after one wash. Looked on line and reviewed part and saw it was a one piece assembly from photos. Removed old assembly by unscrewing from top of washer and screwed new assembly in place.
I removed the old spray arm by pulling it off of the base then I pushed the new one on and made sure it was on properly then I pit the base back into the dishwasher and it was good as new!
First thing I did was turn off the power to the dishwasher, then remove the racks. Remove the foot plates, remove the two top screws holding the dishwasher. Then using the socket set, retract the two foot stands to pull the dishwasher forward. You may not have to do this step as I had to get it over tile. The pully springs are on the sides, easily replaced. After replacing the springs and I recommend replacing both at the same time, put everything back. The hardest part will be the foot plates, there are two and getting them lined up and the screws back in is a bit of a challenge. Then you are done.