FES355YW0 Roper Range - Instructions

Unpluged range for safety (power earlier removed by circuit breaker turnoff).
Removed two screws from front switch cover.
Removed knob from effected switch and removed the wires on the back of the switch.
Removed two screws holding switch and removed switch.
Reversed the process to install new switch.
The entire project took about ten minutes.

1. Turn off circuit breaker, pull out element and remove reflector pan.
2. Unfasten terminal block mounting screw and remove terminal block from casing.
3. Cut wires as close to defective terminal block as possible (not as per instructions) since you will need the maximum possible length of wire.
4. Slip on heat shrink sleeves, strip stove wires and connect to new terminal block per instructions.
5. Heat shrink sleeves per instructions.

Removed 2 screws holding element in place. Pulled out element to access two wires. Slid off the old element connectors. Placed new element in place and attached the two wires. Pushed it back into place and replaced the screws. Done in 10 min max.

Removed 3 screws on bottom edge of door,2 screws on top edge of door. Outside of door comes off. Then use a 1/4 nut driver and remove glass window supports until you get to the inner door glass. Reverse to assemble. Gasket was okey.

Take the time to pull off the door from the hinge; which is to simply pull it up to release with the door open approx. 4 inches. Have a Philips head screwdriver and a nut driver set available. Keep the screws grouped and the take it apart in the logical sequence. It took about 30 minutes total to complete the job. But then again, it was a woman who did it!

took out the old heating elments and cleaned the bottom & top of oven with out the elments in, which made it alot easier then put new ones in. They were very easy to do, just make sure you watch how you took old ones out and don't loose the screws cause you use them to put new ones in.

First I removed the bottom oven drawer from the stove. Then I removed all the screws from the outer oven door. Then I removed the screws from the inter door panel and needed assistance to remove the first glass panel and frame. Then I removed the second panel of glass and frame. Then I removed the third panel of glass that was broken. The gasket was the last part to be removed. Getting the new gasket to stay put while putting the new glass panel next to it was the hard part. I needed assistance to place the glass against the gasket and then place the frame back on this panel. Once this mission was accomplished. It was a matter of getting the next glass panel put back in the frame. and replacing the inter door panel and putting the screws back in. Then I put the third glass panel and screws back in. Once this was accomplished , I put the outer door back and put the screens back in the outer door.

SUPER EASY! The part arrived very quickly. I turned off the circuit breaker, unscrewed the few nuts, pulled out the element and reversed the process. 'works beautifully! Thanks so much.

removed old Plug-in block by removing 1 screw and cutting 2 wires. (Screw was so tight and rusty that I had to use vise grips to remove it). Installed new Plug-in block with wire nuts and heat shrink wraps. YOU just have to make sure the wires are seated in the block properly. This job was much easier than I anticipated. The burner works great now!

Lots of screws but if you have the proper sized nut driver it goes quite easily. Take time to see how the inner glass is mounted to the oven door. There are also screws on the bottom of the door that you need to remove to get the inner panel off. The door itself can stay on the hinges

Simple, just pull out old burners and slide new ones in place. Tried both, they work excellent!

I just had to pull out the old burner and straighten the prongs for the new burner and insert, The prongs of the new burner were slightly bent in shipment, but were easy to straighten with the pliers. The burners were sent in a bag and not a box -- therefore the prongs were easily bent. I was very pleased that I (73 year old lady) was able to fix my stove without a repairman. Saved $$$

REMOVE BACK COVER. UN PLUG, REMOVE TWO SCREWS IN SIDE OVEN, PULL OUT , REPLACE, REATTACH, FIXED CODE F-3

1993 model oven, built in wall model, so didn't to remove oven for the normal rear access to replace the lamp socket. As someone else posted, replacement can be done from inside the oven -- BUT the socket removal was more complex than just 'twisting it out.' But below worked! (1) Turned off oven power at circuit breaker panel. To facilitate working in the oven compartment, removed oven door (2 screws on back of door), raised the over door almost closed, put 2 large nails through the hinge holes when they lined up. Lifted the door out (heavy ~20-25 lbs) and put aside. (2) Put work light inside oven. (3) unscrew glass socket lens and the bulb). (3) Using inspection mirror, studied the inside of the socket to determine that its lock tab type and locations -> were on left and right sides of the socket. These tabs needed to be bent in, but they were each held out by a small circumferential length of think metal, a tab about 3/16" x 3/8". These small tabs could be moved/positioned by just finger friction, with a little start with a screwdriver tip on their edge! I got an end positioned to put sharp screwdriver under that end, then pried it (bent it) inward a short distance. Enough to use needle-nosed pliers to pull it completely out - came fairly easily. Repeated on other side of socket. (4) Then, with pliers, bent each of the 4 locking tabs inward a short distance, Used sharp tool to get one socket edge lifted a small amount; then use mini-pry bar and screwdriver to gently pry around the socket in steps, working evenly around its edge. At about 3/8", it was free. Lifted it inward gently so as not to damage the insulation of the 2 wires attached to its rear. Noted the direction of the wire tabs was straight up (keep same orientation on new socket). (5) Needle-nosed pliers on each connector to gently work the connectors off their socket tabs. Note one tab is larger than the other. Keep the wires inside the oven compartment. Don't damage the insulation. (6) Pushed the wire connectors onto their respective new socket tabs. Aligned socket with the tabs upward, and inserted it, careful to nurse the wires back into the oven wall hole; press socket into the hole, pushing it in evenly and firmly until flush. (7) Pushed in the new type bulb that came with new Socket. Turned on power, and light came on. (8) screwed on new glass cover. (9) Lifted oven back onto the hinge prongs. (easier with two people to get the prongs aligned and into their door slots.) Worked door left and right to get it to lower down fully. Removed nails, lowered door, and put its 2 screws back on. (10) Poured a glass of wine.

Open oven door. Still power to the wall, but all Knobs in "OFF" position. two phillips screws, pull old element back, and disconnect both leads. Put the leads on the new element and reinsert with two mounting screws. Simple.