Models > FEP310GW0 > Instructions

FEP310GW0 Roper Range - Instructions

All installation instructions for FEP310GW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FEP310GW0
31-45 of 106
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken rear stove drawer glide

  • Customer: John from Maysville GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Removed drawer, after removing the 50# of junk in the drawer, Used screw driver to remove screw that holds glide to drawer and then place new part into place put screw into hole and tightened screw. Replaced drawer and told wife not to put 50# of junk back into the drawer.

It was a rather simple fix--just replacing burner pans

  • Customer: Vicki from Jefferson IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Problem I had was finding the right ones to fit the stove top. Burner pans that tell you will fit most stoves, do not. After I had paid over $20.00 for some that did not fit, I got on the internet, found you, ordered the replacement parts and had them within a few days. Put them in and there you go. A perfectly happy me and a nice looking stove again.

Bad Receptacle

  • Customer: TROY from YPSILANTI MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 5 people found this instruction helpful
I had a receptacle melt in front of my eyes. I few questions later PartSelect.com showed me the part I needed and was checking out in less than 10minutes. Part arrived 3 days later and 20 minutes after that it was installed. I'm Amazing!!! No, PartSelect.com is AMAZING!

burner plug broken

  • Customer: Norman from Newport NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
Cut wires removed old plug,new plug in wire nuts on.Put heat on shrink tube done.
Less than 30 min.

Eroding burner drip bowls

  • Customer: Edward from Hamilton OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Removed old drip bowls and installed new, which, thanks to your efficiency, were a perfect replacement

Replace burner drip pan

  • Customer: Ray from Council Bluffrs IA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Removed electric coil replaced pan and reinstalled coil. Part fit just right and no problem.

Both outside door handles turned very beige

  • Customer: Howard from Boynton Beach FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 4 of 11 people found this instruction helpful
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Block broke

  • Customer: Edward from Crimora VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 3 people found this instruction helpful
Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

thermostat knob tore off

  • Customer: SHARON from FRUITLAND PARK FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 3 people found this instruction helpful
my boyfriend took part of the back off unscrewed a few screws took the old one out and put the new one in. It seemed simple to me I was surprised. I knew the cost would have been more than double the part if I had called an appliance technician to do it. I received the part the next day which I was tatally suprised since it was a Saturday. I am very satisfied with Parts Select inventory and service Thank You

Receptacle Assembly has burned out

  • Customer: ANN from MANITOWOC WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 3 people found this instruction helpful
Remove old receptacle and connected and replace new one. Burner now works perfectly again.

back burner would not heat

  • Customer: wayne from whittemore IA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
removed the heating element then removed the screw that holds the plug in on cut the two wires and reconnect the two wires and put back

Ugly looking drip bowl.

  • Customer: Irina from Green Cove Springs FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Repair? What repair? I just removed the old drip bowl and replaced it with the new one. Piece of cake.

the screws fell out of sides and bottom of door,bottom frame was bowed out.

  • Customer: Christine from Clinton Twp. MI
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I had to get someone to help he thought we ordered wrong parts. called part select and was told to call whirpool direct. found out the part was redesigned unkown to us. So we were trying to fit parts that didn't need screws and now I have extra screws that I will send back.

the drip bowls had rusted through

  • Customer: DANIEL from sanborn NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
a really simple fix! the parts came really quickly and all i had to do was pull the heating elements out along with the old drip pans and line up the new pans and push back in. the drip pans weren't 100% perfect as they were a universal fit, and were missing the clips that help the heating elements i nplace, but they look fine and do the job all the same.

burnt out drip pans

  • Customer: Barbara from KAMUELA AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I had been putting off this repair for months! I finally sat down to explore ordering the parts. It was so easy - I wish I did it a long time ago. When the parts arrived, they were exactly what I needed.
All Instructions for the FEP310GW0
31-45 of 106