The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.
1. Loosened 2 sensor mounting screws and removed them. 2. Tripped range circuit breaker to off. 3. Pulled out the range but left gas connected. 4. Loosened the 4 screws on RH side of the top back panel and carefully pried that side of the panel open. 5. Using fingers, threaded the sensor's wiring harness through insulation and into the oven. 6. Unplugged old probe. 7. plugged in new probe. 8. tugged wiring harness back through insulation behind the oven. 9. Using 2 screws removed in 1 above, mounted new sensor. 10. Repositioned top back panel and fastened it in place. 11. Shoved range back in. 12. Tripped range circuit breaker to on. 13. Reset clock. 14. Set oven to 450 for test tun. 15.
Remove the lower bake element by removing the 2 retaining screws that secure the element to the inside oven back. Carefully slide the element out. There are 2 wires attached to the terminals of the element. While removing be careful to not pull the insulation out with the wiring. Attach the wires to the terminals of the new element and reinstall in reverse order.
Turn off circuit breaker Open oven remove two oven racks Position flash light Remove two Phillips head screws that hold the element in place Gently slide out element until you locate the two small wires Gently Detach the two small wires from the back of the burned out element Position the new element in the bottom of the oven and attach the two small wires to the back of the new element Gently slide the element back in place and replace the two Phillips screws that hold the element in place Make certain the new element is lying flat on the bottom of the oven Replace the two oven racks Turn on the circuit breakers and test the oven
Second replacement of switch that disintegrated with minimum normal usage.
Removed old switch, moved the one wire to the same pin on new very cheaply made but expensive made in Mexico switch, replaced switch, pugged range back in too AC, operated new switch, created sparks and smoke. Element now glows to max immediately when turned on. Replaced stove problem gone!
Didn't get repaired because I could not get the right parts to fix it. You would send me a part for the oven. The oven and burner parts are not the same
Burner will not cool down. I have to switch all the way off.
First unplug the electricity from the stove. Replacement terminals on back of switch are set different than the originals. So, I took notes (purple wire =P, Black wire=L1, two yellow wires = H1 & H2, and orange wire=L2). Your stove might be different in the color coding. Just take notes. First I unscrewed the screws on the top back plate of the stove. Removed the back plate. Took notes on where the wires went. Removed the wires going to the five terminals. Unscrewed the two screws on front panel of the stove holding the old switch in place. Removed the old switch. Put in the new switch through the back of stove. Determined the length of the control shaft. Take the switch back out. With two pliers on the control shaft, holding the pliers closer to the switch firmly, use the second pliers just past the predetermined breaking point. With the second pliers snap off the control shaft. Be careful not to snap off two much. Place the switch in the proper place and mount to the stove. You may need some parts in the assembly parts package for this. I did not. Inside of the parts package is a set of plastic parts. I selected the part I needed to insert into the control knob for a bushing just to take up space. I placed that part inside of the control knob. I then placed it onto the control shaft. Plug back the wire going to the electric outlet. Instead of unplugging and plugging, you might want to switch off the circuit breaker and switch back on when the job is done. It works!
Bottom oven quit heating about 6 mos. ago and now top oven quit. Broiler worked fine on both. Bought 1 replacement element to try. Did not work on either oven. Found online where someone had found a bad solder joint on a relay board so I pulled the oven and removed the covers. (WITH POWER OFF. I made a diagram of the wire connections to the board and removed it. I FOUND a cold solder joint on the L2 connection of the top oven board. I found the exact same cold solder joint on the bottom oven board also. After resoldering the connections and touching up any suspect joints I replaced the boards. They BOTH WORKED fine! Anyone that can't solder can take the boards to a local radio/TV repair shop and probably get the techincian to resolder it for a minimum fee. It is certainly worth the attempt.