Models > FDB956RBC1 > Instructions

FDB956RBC1 Frigidaire Dishwasher - Instructions

All installation instructions for FDB956RBC1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the FDB956RBC1
436-450 of 537
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water leaking

  • Customer: Ron from Brick NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove the old part and replaced with new. Done

Water leading from bottom of door

  • Customer: Henry from S Burlington VT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just like the instruction video. I pulled the old gaskets out, cleaned the gunk that had accumulated and put the new gaskets in. The tub gasket does not require any cutting or stretching. Just make sure it makes the turn at the bottom of the tub so the door seals properly. The door gasket was very simple to replace.

Spray arm was melted on end from heating element in bottom of unit. Dishes were not being cleaned well.

  • Customer: Sandra from Wilton NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Replaced arm - SO easy!

The dishwasher was "broken" and it needed to be replaced...

  • Customer: Brandie from Summerville SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
When I looked at my prospective home for the first time, the current "month to month" renters made sure to tell me EVERYTHING that was wrong with the place. One of those things was that the dishwasher was broken and beyond repair. Upon moving in, my brother in law asked "Did you try turning it on??" We did, it worked and drained...so why was it "broken?" The lower spray arm kept popping out mid cycle, then would get melted on the heating units at the bottom of the unit during the drying process. I easily found and purchased the part from this site. Once it got here, I literally just had to pop it on, no tools, no mess. Fixed!

No water comming into dishwasher.

  • Customer: thomas from Neptune NJ
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Cheked supply water line, water there but not getting into machine.Removed screws that hold machine to counter top, lowered adjustable legs and disconnected water line. I turned off power for safety.Pulled machine out about 8 inches to access water valve from the side. disconnect power supply wires, and water discharge hose, remove two screws on valve bracket. Install new valve and reconnect.

The lower spray arm became loose and melted on the heater.

  • Customer: Brian from Weaverville NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Very simple to repair, cleaned the melted plastic from the heater, received the part within 2 days and pushed the new arm into the 2 bracket clamps and it was done. Since this was an older unit they told me the replaceable part number and the price was very reasonable..less then $30 for the whole job!

missing bottom spray arm

  • Customer: Ashley from Normal IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I used the PartSelect repair video online to show me how to fix the dishwasher. I needed a spray arm and support. Excellent video made the repair quick and easy.

Dishwasher leaked around door

  • Customer: Peggy from Hampton VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The new tub gasket just sits right into the grove around the tub. Just press it in (grooved side to the back) all the way around several times and you are good to go. The bottom gasket is hard to see. You have to open the door all the way down and on the inside bottom of the door you will see the outer edge of the gasket going across the lenght of the door. Simply slide it out making note of where the notch in the gasket is located. Slide the new gasket into place (won't go in if notch is on the wrong side) and you are good to go. No tools were required for installing either gasket.

Leaky water under dishwasher

  • Customer: Utahgolf.net from Provo UT
  • Difficulty: Very Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
We have wood floors and in front of the dishwasher our wood floor started warping. We noticed it not getting any better so I looked under the dishwasher and could see a drip coming from the inlet valve. We have wood floors and recent granite counter tops so the dishwasher was stuck and had to hack saw the front legs to remove. Afte all that about an hour an half looked for the part and found it on your site for $25. We were going to replace the dishwasher but decided not to spend $700 for replacement. The part got here in 3 days and I was able to replace it very easy watching your video. It's been about a week and no leak and our floor is dry and back to normal. Thank you, Brent.

Silverware basket developing holes due to age and crystaliization.

  • Customer: Robert G from Merced CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took the new Silverware Basket from the box. Opened door to dishwasher, removed defective Silverware Basket, put new Silverware Basket in its place.

Wheels were broken off and some rust.

  • Customer: Jinny from Tulsa OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took out the old lower rack and inserted the new one. Was worth every penny. New rack slides so smooth.

Dispenser wouldn't stay closed.

  • Customer: Bruce from Kalispell MT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I thought the problem was soap crystal build up, so I tried to file and chip it away, but after replacing the dispenser and checking with a magnifier, I found thet the plastic latch was worn and the dispenser had to br replsced. The video made it easy.

Easy as 1-2-3

  • Customer: Rhett from Laguna hills CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I bought dishracks and a new handle. the dishracks went in without a problem. The bottom one just slides in, the upper one requires removing a plastic latch and somehow getting the middle spout removed, which was difficult. The door handle was easy but required a visit to the hardware store because i didn't have a "torex" screwdriver. Other than that, it was a 15 minute job and it works well now.

Worn stem assembly and lower spray arm tabs

  • Customer: Robert from Brooklyn NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Stem and spray arm tabs worn to the point where every time the washer was used the spray arm would pop off and end up on the bottom of the machine, a screwdriver and ten minutes time saved a ton of money and updated the machine.

Replaced damaged dish racks

  • Customer: jim from Spokane Valley WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Bottom dish rack is a direct replacement with no assembly required. Top rack has to have the old center cone removed and placed onto the new upper rack. The top rack comes with rail wheels in place. In order to reinstall the new upper rack you must take the rail stops off to allow the old top rack and wheels to be removed and then place the new top rack with wheels into the rail grooves. Make sure they are rolling correctly and then replace the rail blocks. Happy dishwashing!
All Instructions for the FDB956RBC1
436-450 of 537