Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FDB4315LFB2

FDB4315LFB2 Frigidaire Dishwasher - Overview

Get Parts and Repair Help for FDB4315LFB2

If you know the dishwasher repair part you need, you can browse the list of all parts on the FDB4315LFB2, or you can search by name or part description. You can also find your part by where it is located on the FDB4315LFB2 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for FDB4315LFB2 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$10.15

Bottom Door Gasket

This gasket is found at the bottom of the dishwasher door and helps prevent water from leaking from the bottom edge of the dishwasher door. If your dishwasher is leaking water from...

$14.50

Tub Gasket - Gray

This dishwasher door gasket creates a seal around the dishwasher to ensure that water is not able to leak out. If this was not in place there would be a gap between the opening of the dishwasher tub and the outside of the door. If this has torn, you might notice leaking water coming from your dishwasher or the inability to shut the door properly. Simply pull out the current gasket, ensure the area is clean, look for the indicator on your new gasket to determine the middle, and press into place without stretching the material. After the repair is complete, shut the dishwasher door and leave closed a few hours to ensure it properly seals into place.

$25.92

Water Inlet Valve - 120V 60Hz

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner of the dishwasher. The attaching solenoids on the valve open and close ...

$3.52

Heating Element Brass Nut

The heating element nut is used to connect the heating element to the dishwasher tub. If water is leaking from underneath your dishwasher, you may need to tighten or replace the heating element nut. Replacing the nut is an easy job, does not require any specialty tools, and should not take you more than 10 minutes. For our step by step guide, click the video below. The brass nut measures 7 inches in length x 1 inch in width x 5 inches in height, and fits most dishwashers. To see if this part is compatible with your dishwasher, check the list of compatible brands below.

$18.98

HOSE

If your dishwasher is leaking or not draining properly, you may need to replace the drain hose. The drain hose connects to the pump located below the lower spray arm and aids in pr...

$48.84

Drain Pump

The pump ejects the water from the unit.

$73.41

Upper Rack Assembly - T3 PRO

This is the complete upper rack and the wash arm.

$20.07

Pulley Spring

Sold individually.

$34.50

Delivery Tube Gasket

Sold individually.

$20.16

Friction Door Cable

Sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The spray arm would fall off during the washing cycle.

  • Customer: Roy from Worcester, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 682 of 689 people found this instruction helpful
Repair was simple. I unscrewed the old grommet which held the old spray arm and screwed-on the new one. About 30 seconds was required. Other people having this problem should note that the spray-arm is made of three pieces which are inseparable when the arm is new. The arm is sold in this form. However, when your machine is having the problem that the a... read more

Bottom Door Seal fell apart and started leaking.

  • Customer: Scott from Flowood, MS
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 223 of 253 people found this instruction helpful
First I opened the door all the way. Second I reached down to the bottom gasket then grabed it on the right end of the seal that is on the right side of the door. Then I pulled the end outward from the bottom of the door toward the heater coil in the bottom of the washer. It came out real easy. You see it just snaps into a little plastic groove under the doo... read more

Leak in the water inlet valve/solinoid

  • Customer: Mickey from Ooltewah, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 140 of 152 people found this instruction helpful
1. Shut off water supply.
2. Removed inlet water hose where it connects to the vavle assembly.
3. Removed the two bracket screws holding the assembly to the frame, and detached the electrical connection from the solinoid.
4. Removed the inlet hose adapter connection from old valve and installed into new valve.
5. Attached electrical con... read more