This dishwasher door gasket (Bottom Gasket, Gasket, Door Seal, Dishwasher Door Lower Seal) helps prevent water from leaking out of the bottom edge of your dishwasher door by creating a watertight seal...
The Lower Spray Arm is used in your dishwasher to spray water and clean your dishes. If broken there will be visible damage or your dishes may no longer be cleaned properly. If your spray arm is broke...
This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing wate...
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, o...
This water inlet valve is usually located behind the lower kickplate panel in either the right or left corner of the dishwasher. The attaching solenoids on the valve open and close according to the de...
The silverware basket, used for dishwashers, is in the bottom dishrack. The lower dishrack basket is used to hold eating utensils such as spoons, forks, and knives, and other small tools. If the baske...
The heating element nut is used to connect the heating element to the dishwasher tub. If water is leaking from underneath your dishwasher, you may need to tighten or replace the heating element nut. R...
This lower spray arm is a genuine OEM part for various makes and models of dishwasher and is sold as an individual part. This part attaches to the lower spray assembly of your dishwasher and the lower...
If your dishwasher is leaking or not draining properly, you may need to replace the drain hose. The drain hose connects to the pump located below the lower spray arm and aids in proper dishwasher drai...
This door spring is manufactured for a dishwasher door. The door spring applies tension to the dishwasher door so that the door does not drop too quickly when it is opening. If the door drops too quic...
This splash shield kit is used in dishwashers and is attached to the lower front corners of the tub. The splash shield is used to prevent water from spraying past the door seal. If your dishwasher is ...
$39.46
In Stock
Questions And Answers for FDB1450CHC4
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Paul
January 4, 2020
Does this model have a vent blower? If yes, is it part of the vent assembly? Can failure of this blower cause condensation build up and leaking from the vent down the inside of the door? I see evidence of a leak trail inside the door starting at the vent opening. There is small leakage onto the floor but not sure where its coming. Wondering if the blower may not be functioning and this causes a "leak".
For model number FDB1450CHC4
Hello Paul and thank you for writing.
This model does not appear to have a blower, but you want to make sure the vent itself is not blocked somehow as this will cause condensation. It still should not leak on the floor. This certainly sounds like it could be a faulty gasket PS9495545 and PS8260227, you should check for signs of damage, and replace if necessary. It is recommended to replace both gaskets at the same time. We hope this helps. Please contact us anytime.
I would like to know the specific measurements of this model. Height , width and depth ...thank you
For model number FDB1450CHC4
Hi Wendy, thank you for reaching out. The dimensions of the given models are approximately 34.25 inches in height, 23.87 inches in width, and 24 inches in depth. We hope this information is useful!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Remove the bottom cover plate. Disconnect the water inlet and black rubber hose. Remove 2 mounting screws. Pull out electrical connector. Reverse order. Be sure to get the brass inlet connector really tight so it won't leak. I did the final tightning after the part is mounted. Not a bad repair at all. The only problem was that it
... Read moreleaked in the first place and messed up my subfloor and laminate flooring.
First I opened the door all the way. Second I reached down to the bottom gasket then grabed it on the right end of the seal that is on the right side of the door. Then I pulled the end outward from the bottom of the door toward the heater coil in the bottom of the washer. It came out real easy. You see it just snaps into a little plastic
... Read moregroove under the door. I then cleaned up the area for food and soap particules. I then placed the new gasket in place by lining up the notch toward the right end with the piece of plastic that encloses the right end of the plastic notch on the bottom right end of the door. Then push it in untill it stops going into the notch. It snaps in but does not make a snaping sound. It just won't go in no more.