Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FDB125RHU1

FDB125RHU1 Frigidaire Dishwasher - Overview

Get Parts and Repair Help for FDB125RHU1

If you know the dishwasher repair part you need, you can browse the list of all parts on the FDB125RHU1, or you can search by name or part description. You can also find your part by where it is located on the FDB125RHU1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for FDB125RHU1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$10.15

Bottom Door Gasket

This gasket goes on the bottom of the dishwasher door.

$14.00

Tub Gasket - Gray

The gasket provides a waterproof seal between the tub and the door.

$25.18

Water Inlet Valve - 120V 60Hz

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the d...

$5.61

Dishrack Roller - Grey

Sold individually.

$26.80

Lower Spray Arm - Gray

This part comes with the heat shield and the tower. It is located on the lower half of your dishwasher. Water is forced through this spray arm by the unit's pump and motor assembl...

$6.37

Heating Element Brass Nut

This nut is sold individually. It is used to install the heating element.

$19.86

HOSE

The drain hose connects to the pump located below the lower spray arm. It aids in proper dishwasher drainage. Size: 7.5 feet long

$40.56

Door Latch and Gasket

Black in color. No longer available in almond. This door latch prohibits the dishwasher from operating when the door is open. The gasket is used around the door to keep the dishwasher from leaking.

$18.27

Door Spring

Sold Individually.

$54.06

Detergent and Rinse Dispenser with Cap

The manufacturer has redesigned this part and it may appear different than the original, but will have the same functionality. This part releases the detergent and rinse aid into the dishwasher.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water leaking from Inlet Valve

  • Customer: CHRIS from ROANOKE, VA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 537 of 544 people found this instruction helpful
Remove the bottom cover plate. Disconnect the water inlet and black rubber hose. Remove 2 mounting screws. Pull out electrical connector. Reverse order. Be sure to get the brass inlet connector really tight so it won't leak. I did the final tightning after the part is mounted. Not a bad repair at all. The only problem was that it leaked in the first ... read more

Lower Rack Roller Missing

  • Customer: Sandra from Mount Vernon, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 363 of 365 people found this instruction helpful
Took the roller out of the package, snapped it into place. Less than 15 seconds. Works good as new. read more

Leak in the water inlet valve/solinoid

  • Customer: Mickey from Ooltewah, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 133 of 145 people found this instruction helpful
1. Shut off water supply.
2. Removed inlet water hose where it connects to the vavle assembly.
3. Removed the two bracket screws holding the assembly to the frame, and detached the electrical connection from the solinoid.
4. Removed the inlet hose adapter connection from old valve and installed into new valve.
5. Attached electrical con... read more