All Installation Instructions for Jenn-Air Range FCE70610B

Broken oven door hinge

Oven is built in. The only way to access the hinges is to pull the oven out and remove the sides.

Parts Used:

Door Hinge Kit

Charles from Lancaster, NY
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set

Was this instruction helpful to you?

Thank you for voting!

Original burner stopped heating up

Unscrewed three screws securing the glass top. Lifted glass top and wedged it open. Took a picture of the current wiring. Removed old burner.Compared male contact points on new and old burner. Plugged new burner in appropriately. Note: The new burner is MUCH hotter than the old one.

Parts Used:

ELMNT-SURF

John from Nesconset, NY
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

leg was bent, also metal receiving bracket bent

Removed stove from slot in wall. Bent rear left leg would not unscrew due to bent metal bracket. Used hacksaw to cut out leg, then straightened metal bracket with small hammer and was able to screw new leg in and adjust height by using level on stove before reinserting stove its slot. Recheck level after pushing back in place and adjust front legs if necessary. If not for bent metal receiving bracket, would have taken much less time. Still easy tho. R'cvd part in two days. Very quick.

Parts Used:

LEVELER-FOOT,SCREW,F/S,NYLON

Virginia from Oceanside, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Wrench (Adjustable)

Was this instruction helpful to you?

Thank you for voting!

Oven was not working, couldn't bake

Amazingly simple. Removed 2 screws, pulled off 2 wire terminals, removed broken element. Re-attached wire terminals, installed screws.......baked some cookies to reward myself. lol Actually, my girlfriend replaced this part. I just talked her through it. Thanks Partselect. I wasn't able to save you any cookies though.

Parts Used:

Oven Bake Element

Bryan from Midland, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Broken leveling leg.

This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.

Parts Used:

LEVELER-FOOT,SCREW,F/S,NYLON

Don from Crestwood, MO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

Was this instruction helpful to you?

Thank you for voting!

Stove would not heat up.Guessed it was element

Pulled stove well away from wall - took plug out of socket..Phillips screwdriver. Slotted element into wire thing-y - one connector fell down the back, so had to take back off the stove. Used tweezers to pull wire back into back of oven. Screwed plate over wire.Was thrilled when I turned stove on and element shone brightly. Husband away so had to do it myself. Had a glass of wine.

Parts Used:

Oven Bake Element

Jean from CliftoN Park, NY
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

replace the heater coil in bottom of oven

It was so easy. The video that was sent to me with my order confirmation made it kids play. Took away any of the fear of doing something wrong. Highly recomend using parts select. Fast servic too!

Parts Used:

Oven Bake Element

Al from Concord, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Erratic oven temperature, would not hold a setting or would get to that setting and then loose it shortly afterward.

Removed two screws on sensor in the oven. Pulled out stove and after unplugging same removed the back panel. Sensor has an electric connection on the rear of the oven with a connection that is easily separated. Threaded new sensor electrical connection through inside of oven and connected on the back of stove. Pushed insulation back around the wire were in goes through to the oven. Replaced back on stove and screwed in two screws which hold sensor inside the oven. Replaced back cover on stove, plugged it in and pushed it back in place. Did the trick for me..

Parts Used: