Quick Question!

Have you ever purchased from PartSelect.com before?

Models > FA4201

FA4201 Amana Washer - Overview

Get Parts and Repair Help for FA4201

If you know the washer repair part you need, you can browse the list of all parts on the FA4201, or you can search by name or part description. You can also find your part by where it is located on the FA4201 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for FA4201 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$36.01

Water Inlet Valve

This is a water inlet valve which is used in washing machines. The valve controls and monitors the flow of water into the washer. It has a multi-mount bracket and outlet adaptor. T...

$7.86

Adjustable Levelling Leg

If your washer shakes or vibrates loudly when it reaches its max speed, make sure the 4 levelling legs are even. Adjust the legs so that the machine is level, and tighten the locking nuts on the legs that are threaded. Your washer should be kept as close to the floor as possible. Your model might have rear legs that level themselves, or it might have threaded legs all around. Make sure the rubber feet have not worn out. Replace any missing or damaged legs and feet. This genuine OEM replacement part is sold individually, so be sure to order the amount you need.

$5.10

Screw, 8/18 x 3/8

This screw is sold individually.

$4.48

Inlet Hose Washer

This inlet hose washer, also known as a high pressure inlet hose washer, is used in washing machines, refrigerators, freezers, and dishwashers. The function of this part is to create a watertight seal in the appliance. If your gasket gets dry and brittle over time it will start to crack and will lose its function. In this case, it is important to replace it. Refer to the manual provided by the manufacturer for further installation instructions and accurate guidance. As a safety precaution, remember to unplug your washer from the power source before beginning.

$5.20

Rubber Foot Pad

This foot pad is just over an inch in diameter. It is all black in color and is made entirely of rubber. This pad is used for the levelling legs of many washing machines.

$4.87

Nut

$4.79

Screw - 8-18 x 1/2

Sold individually.

$3.02

Screw, Ground

$13.77

Nut

This part is sold individually. This nut can be found in various appliances including a dishwasher, air conditioner, washer, dryer, range/cooktop, oven, freezer, range hood, and re...

$5.07

Single Washer Inlet Strainer

Found at the end of the inlet hoses.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Cold water valve only opened to a trickle

  • Customer: Brian from El Cajon, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Wrench (Adjustable)
  • 197 of 207 people found this instruction helpful
I started by unplugging the appliance and then shut off the hot and cold water faucets then I disconnected and drained the hoses. Next, I removed the two screws that held the valve assembly in place. I then pulled the assembly out about 3 inches and disconnected the two wire plugs. The last step was to loosen the hose clamp on the outlet hose and pull off... read more

washer filled with water even when OFF.

  • Customer: wayne from lees summit, MO
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
  • 37 of 41 people found this instruction helpful
Followed your directions and it went very easy.
Only took maybe 30 mins.
I was impressed with your trouble shooting and inst!!!!

Thanks

wayne read more

Cold water solinoid not opening properly

  • Customer: Erich from EastHampton, CT
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 36 of 40 people found this instruction helpful
I moved wash machine away from wall and unplugged from wall outlet. Shut off water, then removed hot and cold water lines from water inlet valve,removed screw from mounting plate and removed valve from wash machine. Checked to see if replacement valve was compatible (exact fit).
Unscrewed the two screws holding valve to mounting plate,unscrewed hose cla... read more