F120 - Instructions

Remove where the water pumps are and remove the one that was damaged easily

Do not pay a service company to come to your house to make this fix!!! If you have common sense, simple tools, a phone camera and some mini zip ties you can do this!

After watching a couple YouTube videos on installing a new motor I had the confidence to start the job. My biggest worry was I'd forget where a screw/part went so I took a lot of pictures as I disassembled. I also laid all the parts out on a table reflective of where they belonged on the machine. I learned washers aren't rocket science - YOU CAN DO THIS. The most difficult part of the fix was my washer was a different model so much of the caging was completely different than YouTube disassembly, but once I got into the machine it was fairly identical. Easily popped out the old, broken motor and inserted the new LG certified part. Reassembled in 1/2 the time of disassembly and my machine works like new:) Hoping to get another 10+ years out of this washer.

Thanks PartsSelect for the high quality certified LG part. Very nice quality and weight.

Just put in the new one.

Totally dis-assembled this washer to check the bearings and drum plus fix the pump problem. We wash dog blankets occasionally and found the little drain hose from the front door gasket was clogged with hair. It makes a 90 degree turn and it gets caught there. THAT fixed the smell issue. As far as the pump replacement goes its quite easy. Videos online are your friend.

Follow the LG washer video.

1 tilt washer back
2 remove cover plate screw from front of drain filter access panel.
3 Remove cover plate and remove 2 more mounting screws .
4 go below washer and pull down sliding clip and move pump assembly back.
5 remove wires and 3 mounting screws around pump housing
6 Swap pump and re-attch wires

Used Youtube to look for a set of repair instructions. From start to end 35 min.

The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.

Overall very easy to do.

Line up the plunger with the existing slots in the door and push in.

NOTE: When testing it was evident that the magnet was not as strong as the original one. I would rate as one step up from useless.

This was a very easy repair. Just followed the steps in the videos on the website (I replaced both the hot and cold inlet valves, so two different videos, but the process for each is similar) and it couldn't have been simpler.

Not too bad, had a neighbor help with the project as washer/dryer were stacked. removed dryer from on top out of way. Drained washer, tilted on side to get access from down below. Second person help here. unscrewed drain pump from front, Used pliers to unclamp hoses, disconnect wires to motor (already pulled power from wall) pushed plastic clip holding in unit and pulled out. New unit was factory new, not a knockoff. We took extra time to clean out hoses, especially from the main washer unit, it was a simple unscrew clamp and pull hose down. We sprayed out gunk from hoses and parts going back in. Once new unit was ready, installed back and reconnected hose and power. The clamps were somewhat of a pain with the overall size and angles to get them seated and on correctly. Much easier to take off, but take the time to reinstall correctly. Don’t need water leaking. Motor much quieter now, wife is happy.

pops right into hole

2 hose clamps and a hose, easy! This would be a very common cause of leaks in washers due to all the movement inside.

I already had the top of the washer open, from previous disassembly to clean the front loader seal, and when I ran a trial load, noticed a small 1/4" tear in the hose bellows that attaches to the drum.

Very simple repair, remove the existing hose by loosening the clamps, paying attention to their orientation. Install the existing hose clamps onto the new hose, install and tighten the hose clamps.

5 minute job, if the washer top is off (which is also simple).

After watching the video for installation of the bellow, I followed the suggested repair method and was able to repair my washer.

Simply inserted new plunger/magnet back into door with thumb&finger until you hear the little locking tabs click. No tools required.