EWU1005 Maytag Dishwasher - Instructions

I unscrewed the parts of the washing tower, then removed the housing and filters above the impeller. Lastly I removed and replaced the impeller and "o" ring. This repair went fine. Unfortunately another part (blower) let go and I decided not invest any more time or money into this machine since it was so old.

Pull old gasket off (30 seconds), take panel screws out of front panel and control panel, carefully lower control panel push tabs thru holes from inside door, once all tabs in, push door closed and take pliers and pull tabs until they lock into place, put panel back together. not that difficult, my wife and I had it back in working order in approx 30min.

I used the parts blowup diagram on PartSelect.com and dissasembled the bottom wash assembly. Carefully examining how the washer arm rotated, I determined that the spray arm support nut had broken. The extended top of it has broken off. This nut, when tightened, allows the spray arm to rotate freely. In trying to diagnose the problem, I had even removed the motor assembly at the very bottom. When I reassembled it, I apparently did not seat the gasket well and did not tighten the bolts well, so when I tested the washer, water leaked out the bottom. So, I had to dissasemble it all again and properly torque the bolts. So, I really created another problem during the diagnosis.

Put spring in plastic bushing, snapped into door arm and hooked opposite end of spring in first hole. Repeated process on opposite side of door. Did the above without moving the dishwasher from installed position.

On my maytag portable dishwasher I had to remove three side screws on right lower panel,and two lower screws to free up panel. I had to pry the panel away from the body to get axes to the springs. Replaced springs as instructed reinstalled all hardware, finished.

After nearly 20 years of use (and no service) my Maytag dishwasher stopped getting dishes clean. I called Maytag and they made me an appointment with a nearby service center. The Maytag person also suggested I do a run with an open container in the dishwasher filled with a couple of cups of white vinegar – since that dissolves the white scale buildup from hard water. That helped a lot. Yay Maytag!

I had 5 days to wait for service, so I started Googling. I found very negative reviews of my local service center, but I also learned that I could buy a replacement detergent dispenser online and I found excellent simple instructions for installing it. It arrived in two days and I installed it. The hardest part was removing the front panel of the dishwasher to get access and supporting it while taking out the last couple of screws – then holding it in place afterwards while putting the screws back in. I recommend having a second pair of hands!

I also realized that the two rotating spray arms (at the bottom and at the top) weren’t rotating! They’re easy to remove (just unscrew the center component), and I found that many of the holes were clogged – including all the ones pointing sideways that make them spin. I had to force water inwards through the holes to dislodge the debris, then I filled the arms with water through the center hole and sloshed it around to clear things out. That worked. I put it back together – and the dishwasher is now as good as new!

For good measure I took the cover off the strainer in the bottom to clean it, but surprisingly the strainer was almost completely clean.

I cancelled the service appointment, of course. I’m sure I saved a lot of $$$.

I had read that recently mandated reformulation of dishwasher detergent with lower phosphate content makes it less effective – but I’m not seeing that: a little simple maintenance and my dishes are 100% squeaky clean again!

I opened the door and pulled the old gasket out using a flathead screwdriver to pry up the difficult to remove areas. I cleaned the area with a damp cloth and place the new gasket in the slots. The entire process including the cleaning took no more than 10 minutes. It was so easy. By the way, I had the part in my hands 2 days after ordering it. I am very impressed with the service.

Removed the 6 screws holding the pump and motor assy. Disconnected the two hoses and wiring connector. Removed the motor and pump, removed the pump parts to get down to the impeller. Removed the old impeller (one screw) and installed the new impeller. Put every thing back together and it worked fine. Every one is happy!

had to pull the unit out abour 6" and simly replaced the springs - it was easy

Removed the front of the door by removing 2 screws in each side.

Remove 2 screws on each side holding control panel

Removed old gasket by pulling it out, and installed new gasket. Used needlenose pliers to pull tabs securely into slots.

took the cover off and replaced the filter. It works great now.

The Retaining Nut of my Upper Spray Arm fell off and was stripped. I was thinking I was going to have to get a new dishwasher because mine is pretty old. I found Partselect.com and plugged in my model number and it gave me all the parts. It cost me less than $10 with shipping and it saved me about $450.

Remove the lower panel by taking out the 2 screws on top and 2 at the bottom of the panel. To diagnose the problem, verify that there is water supplied from the valve under the sink to the water supply valve under the DW. This can be done by turning off the valve under the sink, disconnecting the copper supply line under the DW then turning on the valve under the sink to see if water passes through the line.

The float switch is located on the left front (as you face the DW). This is activated by the float in the tub. Check to be certain that the float is not restricted. The contact point on the switch is a spring loaded plunger. It should depress as the float rises and pop back out as the float returns to its low point.

Turn off the circuit breaker for the DW. To remove the switch, pull off the two electric leads from the switch. Mark the top lead with a piece of tape. Then remove the one philips screw. Replace the switch by reversing the procedure. Note that you have aligned the float contact point with the float.

Removed covers on the bottom of dishwasher so I could get access to area. Measured no voltage on water inlet pump. removed to wires from foat switch, one screw to remove float switch. When I pressed the float switch button to activate the switch would not move. Ordered and replaced the switch. 30 minutes tops

i removed the bottom spindle inside of the washer compartment. laid the pieces out in order of which they were removed. found the impeller was busted where it attaches to the shaft of the motor. screw was missing but found it laying in the bottom (there is a screen that filters the water as it drains). replaced impeller and put parts back together in order. good as new.