EV188NYWS00 Whirlpool Freezer - Instructions

Great service. Unpluged old switch and pluged in new one. Works great

removed the 2 screws that held the panel in place, had to reach up and push on locking tabs to lower trhe front of the panel. was able to then push on the locking tab of the switch to release it. removed the wires, replaced them onto the new switch, and snapped the switch into place. the rest was reverse of the uninstall process.

At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT

We had a refrigerator that had no ice maker at all, but it had the wiring behind the freezer panel and the wiring for the solenoid valve at the bottom of the refrigerator. The installation went easy for me, but I do not think the average homeowner could handle it. There are always little variations from model to model so some of the diagrams were not quite the same as my unit. But all the necessary parts and hardware were there and the install went fine. its crabnking out perfect ice like crazy.

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

Rather than pay a repairman an assessment fee, then the cost of the repair to the existing icemaker, I decided to replace the icemaker for a lot less. The Add On Icemaker kit came with installation instructions. The kit included the ice maker, as well as the hose and water feed control on the back. Originally, I was nervous about attempting to replace the icemaker. I watched a video on YouTube about replacing an icemaker and saw how easy it could be. Following the enclosed directions, and Wow!, it was extremely easy to remove and add the new icemaker. Don't pay to have someone else do it! This is a no-brainer.

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

My husband tackled the job....but before this repair he had to replace ours at home so he had some experience at it....although...on this fridge he had to hook up the water line and all...but basically was not too hard...and the ordering of the part and delivery was excellent...

I had the best luck using pliers to remove the hex top screws. Once the screws were removed I unplugged the old defrost timer and plugged in the new one. Replaced the screws and the freezer worked when plugged in.

googled the model of ice maker and refrigerator, ordered replacement ice maker from Part Select. Received next day, installed it in 10 minutes and it worked like a charm.

I removed a few items from the freezer to make room. Husband took out the old ice maker. (We were sure it would require moving the refrigerator out which would have been a huge undertaking given the tight fit) To start he simply replaced the ice maker with the new one. I started watching...and even though it says that it will take up to 24 hours to make ice, it began making ice probably within an hour! After about 6 batches, I threw those out. (just in case there was anything in the line that would contaminate the cubes)It is obvious that the old one had not worked properly for a long time! The ice container is full to almost over-flowing! It has not been this full in a very long time, as I use ice every day! Simple fix! And might I add...LIGHTNING FAST DELIVERY!! It was here in two days! We are thrilled!!!!!