Models > ET20DKXBW00

ET20DKXBW00 Whirlpool Refrigerator - Overview

Get Parts and Repair Help for ET20DKXBW00

If you know the refrigerator repair part you need, you can browse the list of all parts on the ET20DKXBW00, or you can search by name or part description. You can also find your part by where it is located on the ET20DKXBW00 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for ET20DKXBW00 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.58

Light Bulb - 40W

Sold individually.

Order within the next 33 mins and your part ships today!
$13.94

Defrost Timer Kit - 120V 60Hz

This eight-hour defrost timer will replace most other defrost timers. This device acts like a clock. It continually advances and alternates between activating the cooling cycle and the defrost heater. The best way to make sure you get the correct timer for your refrigerator is to conduct a search for your model number.

Order within the next 33 mins and your part ships today!
$21.36

Bimetal Defrost Thermostat

This clip-on thermostat will sense the temperature increase in the evaporator during the defrost cycle and will cycle the defrost heater off after the ice or frost is melted.

Order within the next 33 mins and your part ships today!
$5.55

Icemaker Water Fill Tube Kit

This kit comes with a fill tube and a compression nut.

Order within the next 33 mins and your part ships today!
$37.79

Condenser Fan Motor Kit

This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a blade mounting nut, and a cushion. This part provides forced-air ...

Order within the next 33 mins and your part ships today!
$6.80

Door Shelf End Cap Set

This door shelf end cap set contains two white end caps. Each end cap can be used as either the right or the left side. These end caps also come with adhesive strips and an instructions sheet.

Order within the next 33 mins and your part ships today!
$20.61

Shelf Support Stud

This is a 12 piece kit.

Order within the next 33 mins and your part ships today!
$40.84

Evaporator Drip Tray

Order within the next 33 mins and your part ships today!
$2.07

Screw with Washer

This metallic screw is less than an inch long and comes with a plastic washer.

Order within the next 33 mins and your part ships today!
$42.63

Evaporator Fan Motor Kit

The evaporator is found in the back of the freezer. This kit comes with two mounting grommets, two sleeves (not to be used on porcelain models), two #8 mounting screws, and a push-on fan blade.

Order within the next 33 mins and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The frost free feature of the freezer was freezing over with ice and cooling coils were being insulated with thickening frost which caused the cooling air to rise in temperature from -5 degrees to 20 degrees.

  • Customer: Lawrence from Grahamsville NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver
  • 241 of 284 people found this instruction helpful
I troubleshot the problem by reading the electrical schematic and concluding the heating elements (defrost cables) were either defective or the bi-metal temp sensor was open. When closed the temp sensor completes the circuit for the current to flow through the heaters to defrost the cooling coils every 8 hours and then when the bimetal opens at 55 degrees t... read more

Sometimes the condenser fan would start causing the refrigerator to overheat.

  • Customer: Tom from Franklin WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 96 of 102 people found this instruction helpful
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire a... read more

Broken elbow on icemaker water fill tube.

  • Customer: Charles from Orland Hills IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 77 of 84 people found this instruction helpful
Removed 2 screws holding water fill tube to rear of refrigerator and pulled out, matched old part with new to make sure of proper match. Guide new fill tube thru hole, making sure it is aligned with slot in ice cube tray on inside of freezer. Install new plastic line from water pump outlet to water fill tube, check for leaks, job done. read more