ESS23XGSAWW General Electric Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
would not "dump" ice cubes
I am more than 80 yrs, always thought I could fix just about everything--but, this looked complicated. Once I received the new icemaker; took a good look where the screw-holes, etc. were, then removed the "old" one. Took about 20 or 30 minutes, then the "new" one was easily installed.
Parts Used:
-
Phayo from Lake Charles, LA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
no ice or water. clicking noise.light on door dim and gets dimmer when trying to dispence ice
removed cover for main board, unplugged wires,pinched 4 clippes with needle nose pliers,removed old main board,installed new main board in reverse order. replaced cover and plug in fridge and everything was working like new
Parts Used:
-
richard from north andover, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
The Plastic Auger broke apart
-
William from New Braunfels, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Unusual noise from freezer.
Replaced above parts and the noise problem was not resolved. Ordered a new motor, fan blade and another set of grommets from PartSelect. The parts were delivered the next day. Took me about 15 minutes to swap the new parts in. It's been 3 days since the repair and the noise has not returned.
Parts Used:
-
Vincent from Lyndhurst, NJ
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Refrigerator freezing.
Temp. Sensor was under an egg shaped cover on the left side wall in the refrigerator. Remove the cover, cut the two wires to the old sensor and remove it. Connect the new sensor to the two wires using butt connectors. Replace cover and done.
Parts Used:
-
Wayne from Rancho Cordova, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
No water from dispenser
Just like installation video said. One error I did not read first note that check to see if line was frozen, which it was. Nothing wrong with valve, but changed it anyways. Works great now. Thank for all the help. You all are great.
Parts Used:
-
Mike from Brooksville, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Tange on ice maker stopper arm broken, would cause icemaker to hang up and not produce ice.
I followed the instructions from this manual . I was a little concerned that I might break the new stripper arm. But after removing the old arm I was able to practice the technique and installed the new arm with no problems.
Parts Used:
-
John from Charlotte, NC
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice bin auger broke near discharge end. Not dispensing ice very well.
Viewed the video associated with the part before it arrived. Really helpful to understand the sequence of disassembly, reassembly, and a few tricks to anticipate. Went just as advertised!
Parts Used:
-
Jean from Maumee, OH
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Noisy Howl from Freezer "Awwwwooouuuuuuu" (Repeat)
Parts were perfect. Shipment great. It took a bit of time to get back to the Evaporator fan, so i basically had to take the entire freezer apart. Not a problem. The one issue i ran into was my unit had 2 white wires which connected to a silver bullet thing, that were not included in the wiring harness. Maybe I could have ordered that part (thinking out loud) I had to cut the old one apart, and adapt them into the new one, which had 2 holes to spare for this purpose. I guess i could have spliced every wire, but didn't. The freezer now SOUNDS LIKE A FREEZER. Thanks,
Parts Used:
-
Rich from Venice, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Was this instruction helpful to you?
Thank you for voting!
ice falling out of the door onto floor
Ordered part using the schematic, it got here the next day!! Took out the ice bin, using the 2 butter knives, I pried the side clips and slipped the dispenser out, , I removed the broken plate, and carefully threaded the auger into the hole of the new plate, slid it into the dispenser and seated clips, placed back into ice bin and attached the 3 screws on the bottom to hold in place! A 70 yr old lady repairman, who would have thought it.
Parts Used:
-
Mrs.Bobby from Thomasville, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!