EMO3000CCC001 General Electric Microwave - Instructions

Followed suggestion by previous poster to remove bottom panel...facilitated process well

Unplug, Put Towel on cooktop. Took out screws on bottom and lowered. Removed two screws holding motor in place, Attach new motor to leads and screwed in place, Put up bottom and screwed in place. Easy, fast and works great.

followed the easily understood step by step instructions from the owner's manual

I read about this problem on google-E How? The instructions said to break gently off the hook and let the inside fall down. I did try to bring entire hook out, but the way the hook is designed. It did not come out out of hole. I then gently placed new hooks into hole. part number WBO6X10224, PS227935, PS227934. Then I popped a popcorn bag and Presto!.

Very easy to replace the light socket. Unscrew screws under microwave to lower the base. remove screw at rear of light socket. Unplug power to socket. Plug wire into new socket. Replace new socket into base and replace serew. Hold base plate up to microwave and replace all screws. Do yourself a favor, if replacing one of the lights, go ahead and do both. Shipping cost is the same for 1 or 2 bulb sockets.

SOOOOO simple. Ordered drive motor. Unplug microwave. Take off bottom plate, 6 screws. Unplug wiring from motor. Unscrew drive motor. Replace with new one. Screw on, plug to wiring, screw plate back in place, plug in microwave. Walla!!! It works great.

Installation of the damper was effortless but removing the microwave, cutting holes vertically through an overhead cabinet then installing ducting with a ninety degree bend, through another cabinet, and then through outside wall consumed most of the time and effort.Your service, packaging, and timely (next day!) were extremely helpful.

Remove bottom plate of microwave. Remove old drive (one screw) replace with new motor and replace bottom plate.

Fist I removed the 5 screws under the microwave. Then I dropped the panel and accessed the socket. I removed the socket by removing the one screw and disconnecting the wires. Replaced the wires on the new socket, installed the new bulb and reattached with the screw. replaced the panel with the 5 screws and I was done. Easy

Opened the microwave oven door, unscrewed two screws which held the control panel on, then I removed two of the door switches (each had two screws), and then used the continuity tester to see which one was not operating. It turned out to be the secondary door switch, replaced it and to my amazement, the microwave worked. I have never repaired an appliance before but I didn't want to replace our over-the-stove built in microwave. It was the best day ever when it was working again! The hardest part was getting myself to try the repair.

Took out the 2 screws holding the front grill on. Took out the old filter and put in the new one. Then put the grill back on...DONE!!!

damper plate was a snap-in part. rotated fan discharge to top of microwave. installed ducting to discharge food odors outside.

Watched How to repair a Microwave that turns on when the door is opened Video on the web. From this took a shot at the switch was the problem. When I removed the switch it was defective. The small button was in and when you turned the switch upside down the button would drop back into position. Ordered a switch for $25.oo , installed it and the microwave is working fine.

Unplug appliance, Staring from the rear sides, remove the four side screws. Remove the left and right front screws and finally the front center screw. The bottom panel hinges down toward the rear . Unplug the input wires from the sockets . Unscrew the two retainer screws (one each) and pull the sockets out of the panel. Note that the retainer screws are shouldered. The shoulder fits through the elongated slot in the socket. Screw the bulb into the socket and insert through the mounting hole. Insert and tighten the mounting screws. Note that the sockets may appear to be a bit loose. That's OK because of the shouldered screw. Don't over tighten or you risk stripping the threads of the panel. Plug in the input sockets and install the panel screws in the reverse order of removal. Plug the appliance in and test the bulbs.