EMO3000CBB04 General Electric Microwave - Instructions

Once I read more on Partselect about how others had removed adjacent parts, I found it extremely easy. I had previously thought I would have to remove the microwave from the cabinet prior to repair, but once I looked at Partselect's expoded view of the microwave, it all became clear and took me longer to clean up than the actual repair.

Piece did not fit as well as old piece needed to take off a small piece to make it fit. Once it was in the turntable worked again

Removed screws and old parts. Fitted new part to door and put screws back in.

Phillips screws on bottom panel allowed me to install new socket and put electric connection back. Secured bottom panel and that was it.

Remove top air grate via 2-screws. Remove metal top panel behind grate that's above bulb via 1-screw. Bulb is exposed and can be un-screwed. DONE

Followed the online videos to enter the cavity to the switch holder. Noticed right away the dreaded capacitor was in back right corner behind where the touch pad had been removed. I isolated the capacitor with an old computer mouse pad for extra safety. Took some manipulations to get the switch mount out from behind the wire bundles. Once out front, easy to use small flat blade screwdriver to release each switch and replace with matching new switch. Only one switch was bad but replaced all three. Back together and working great.

My microwave was squealing horribly and replacing the turntable motor (SUPER easy btw) didn't fix it. So I figured it was a spun bearing or bushing in the cooling fan (spoiler alert -- it was!). Installation was simple and did NOT require removing the cabinet-mounted microwave from its position above our stove: Unplug microwave, carefully unscrew the 2 screws holding the vent grate above the door, remove the grate, then unscrew the one screw holding the top of the control panel to the case. Carefully pivot top of control panel down and unhook it from the case (at the bottom of the control panel there are two little legs or extensions that insert into slots in the case). Then disconnect the 3 or 4 wires that attach the control panel to the wiring harness (I marked them each with tape so I would remember where they go, but you can just take a picture with your phone). Set the control panel aside. Where the control panel was, you will be looking at the fan, with a bunch of wires between you and it. Take another phone picture for reference, just in case. Disconnect the various wires, starting at the top right and working your way around clockwise. I marked each wire with a piece of tape and a number, starting from 1 and working my way around an imaginary clock face. I think I got to 12 and then the last two (sort of buried in the middle) I labeled as "0" and "-1" but you can use any numbering series you like. Once the wires are all disconnected you can gently push them aside and unscrew the two screws holding the fan assembly in place, and disconnect the fan wire. Then gently maneuver the fan assembly out the front of the case. Installation is simply the reverse of this simple disassembly process. Voila! Back to a nice quiet microwave.

I removed 4 screw from the under carriage of the microwave then, removed the 2 screws from the motor, replaced the motor and replaced the screws. It was so easy it took only 4 minutes to perform, better than replacing the whole unit (microwave) and less expensive too. i only wish it was made in the US, I wouldn't mind to spend a little more.

I used the internet and your directions to complete the repair. It was easy!

Removed broken coupler hub and pushed new hub on shaft. Make sure to align the new hub correctly when pushing on to shaft. Repair took less than 1 minute.

First I replaced the cracked cooking tray and I was done.

removed electrical wires, unscrewed holder, inserted holder, attached wires, added bulb, and put cover back on.

New one arrived very quickly.

Right part. Right on time. Fit like it should.

Excellent service.

First I figured out how to take the door apart to remove two hidden screws, once that was done it was easy to install the new part. The part came extremely fast and worked well. The picture with each part labeled helped too!

Placed the screws in the proper areas, used the screw driver to tighten down and I was in business with light to spare. I am happy to have found the proper screws.
Thank you.