EL7JWKLMQ03 Whirlpool Refrigerator - Instructions

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

put the new gasket in a tub of hot water. remove door and lay on flat surface, remove old gasket and pull hot gasket from tub, dry and install, the hot water helps remove the wringles from shipping.

I unplugged and defrosted the freezer ( good excuse to give it a good cleaning). I then removed the hex screws from the door under the gasket. Because this attaches the door panel to the freezer, it is helpful to have two people for this task if you have a full size upright freezer. We then removed the panel, cleaned the door, and fitted the new gasket in place. If your gasket has kinks in it, either throw it in the dryer on low for a few minutes or use a hair dryer to smooth them out. We then added a few screws around the center point of each side to hold the gasket in place, secured the corners, and replaced the remainder of the screws. We used a small cordless drill. The gasket will be hard at first, so I duct taped the freezer door shut with a few pieces of tape and turned the unit back on. A repair guy was going to charge me $350.00 for the job, but I did it for free with the cost of the gasket. This site is the least expensive place I found anywhere, and shipped very quickly!

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

Removed panel and replaced the fan and clip when it arrived from PartSelect. The job was not big but having a part outlet with the item in stock was a real joy. In a few days we were back with a silent running freezer. So quiet now that I have to open the door to confirm that it is still running. Thanks Part Select. Bryan L. Huth

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

I had the best luck using pliers to remove the hex top screws. Once the screws were removed I unplugged the old defrost timer and plugged in the new one. Replaced the screws and the freezer worked when plugged in.

Had to remove 3 trays of food to get to the panel where the fan was, remove 4 phil screws found the fan had a broken blade. Went on line found the part at partselect order it recived it in 3 day. Removed the fan had 2 screws use nutdriver, removed old fan blade install new put everything back freezer is working fine.

Viewed the viedo - it showed what to do

First filled tub with hot water and placed new gasket in water to limber up. Removed Door, placed on a table, removed all screws and removed door insides and old gasket, Cleaned all parts, dried new gasket then put back together just in reverse of removal, moved fridge back into place turned back on and it was cooled back down in about 15 min. working great. Now it has the same vacuum on it as when it was new.